Manuals / TP-Link / Computer Equipment / Network Router

TP-Link 1910010933 manual Logs, ¾ Daylight Saving TimeDST State, ¾ Daylight Saving TimeDST Config

Models: 1910010933

1 124

Download 124 pages 9.3 Kb

Page 116

¾Daylight Saving Time(DST) State

The following items are displayed on this screen:

¾Daylight Saving Time(DST) State

Show the work state of DST.

¾Daylight Saving Time(DST) Config

DST Status:

Enable or disable the DST.

Predefined Mode:

Recurring Mode:

Date Mode:

Note:

Select a predefined DST configuration.

zUSA: Second Sunday in March, 02:00 ~ First Sunday in November, 02:00.

zEuropean: Last Sunday in March, 01:00 ~ Last Sunday in October, 01:00.

zAustralia: First Sunday in October, 02:00 ~ First Sunday in April, 03:00.

zNew Zealand: Last Sunday in September, 02:00 ~ First Sunday in April, 03:00.

Specify the DST configuration in recurring mode. This configuration is recurring in use.

zTime Offset: Specify the time adding in minutes when Daylight Saving Time comes.

zStart/End Time: Select starting time and ending time of Daylight Saving Time.

Specify the DST configuration in Date mode. This configuration is one-off in use.

zTime Offset: Specify the time adding in minutes when Daylight Saving Time comes.

zStart/End Time: Select starting time and ending time of Daylight Saving Time.

●When the DST is disabled, the predefined mode, recurring mode and date mode cannot be configured.

●When the DST is enabled, the default daylight saving time is of European in predefined mode.

4.8.6Logs

The Log system of router can record, classify and manage the system information effectively.

Choose the menu Maintenance→Logs→Logs to load the following page.

-111-

Image 116

TP-Link 1910010933 manual Logs, ¾ Daylight Saving TimeDST State, ¾ Daylight Saving TimeDST Config

Contents

TL-R480T+ Load Balance Broadband Router REV6.0.0 1910010933CE Mark Warning COPYRIGHT & TRADEMARKSFCC STATEMENT Safety Information 安全諮詢及注意事項CONTENTS Chapter 3 Quick Installation GuideChapter 4 Configuration Chapter 1 About this GuideHardware Specifications GlossaryAppendix A Appendix BPackage Contents Symbol Chapter 1 About this Guide1.1 Intended Readers 1.2 ConventionsAppendix B FAQ Provides the possible solutions to the problems that may occur duringthe installation and operation of the router Appendix C Glossaryz Powerful Data Processing Capability z Powerful FirewallChapter 2 Introduction 2.1 Overview of the Router2.2 Features z Easy-to-useHardware Basic Functions2.3 Appearance 2.3.1 Front PanelSecurity z LEDsz Reset button z AC Power Receptacle2.3.2 Rear Panel z Interface DescriptionChapter 3 Quick Installation Guide 3.1 Configure PCPage Page Is the connection between your PC and the router correct? 3.2 LoginIs the TCP/IP configuration for your PC correct? Figure 3-8 Quick Setup Figure 3-9 WAN ModeFigure 3-10 WAN Port Figure 3-11 WAN Connection TypeFigure 3-13 WAN Connection Type - PPPoE Connecting Figure 3-12 WAN Connection Type - PPPoEIf you have difficulty in this process, please contact your ISP Figure 3-14 WAN Connection Type - Dynamic IPFigure 3-15 WAN Connection Type - Static IP Figure 3-16 WAN Connection Type - Static IP Connecting Figure 3-17 Configuration CompletedChapter 4 Configuration 4.1 Status4.2 Quick Setup 4.3.1.1 WAN Mode¾ WAN Mode 4.3 Network1 Static IP ¾ Static IPChoose the menu Network→WAN→WAN1 to load the configuration page Tips2 Dynamic IP Default GatewayPrimary DNS Secondary DNS¾ Dynamic IP z “Connected” indicates that the router has successfully obtained ¾ Dynamic IP StatusSelect this option to enter the DNS Domain Name Server address 3 PPPoE Primary DNS Displays the IP address of your ISP’s Primary DNSSecondary DNS Displays the IP address of your ISP’s Secondary DNS Figure 4-5 WAN - PPPoE¾ PPPoE Settings on. The connection can be re-established automatically when it576-1492. The default MTU is 1480. You are recommended to keep Enter the Account Name provided by your ISP. If you are not clearHere allows you to configure the secondary connection. Dynamic IP Dynamic IP is selected, the obtained subnet address of WAN port is¾ PPPoE Status manually terminated or the router gets no response from4 L2TP Figure 4-6 WAN - L2TP¾ L2TP Settings Enter the Account Name provided by your ISP. If you are not¾ L2TP Status Default GatewayIP Address Subnet Mask5 PPTP Displays the IP address of your ISP’s Secondary DNS¾ PPTP Settings PasswordActive Mode Connection Type¾ PPTP Status Default GatewaySubnet Mask Upstream Bandwidth¾ BigPond Settings 6 BigPond¾ BigPond Status been¾ LAN 4.3.2 LAN4.3.2.1 LAN ¾ DHCP Settings 4.3.2.2 DHCP4.3.2.3 DHCP Client 4.3.2.4 DHCP ReservationActivate or Inactivate the corresponding entry ¾ DHCP Reservation¾ List of Reserved Address 4.3.3 MAC Address Set the MAC Address for LAN portSet the MAC Address for WAN port ¾ MAC Address4.3.4 Switch 4.3.4.1 Statistics4.3.4.2 Port Mirror ¾ Statistics¾ General ¾ Port MirrorTips 4.3.4.3 Rate ControlApplication Example 4.3.4.4 Port Config ¾ Rate Control¾ Port Config 4.3.4.5 Port Status4.4 User Group 4.3.4.6 Port VLAN¾ Port VLAN Tips¾ Group Config 4.4.1 Group4.4.2 User ¾ List of Group¾ List of User ¾ User Config4.4.3 View 4.5.1.1 NAT Setup ¾ View Config4.5 Advanced 4.5.1 NAT¾ NAT-DMZ 4.5.1.2 One-to-One NAT¾ NAPT Activate or inactivate the entry ¾ One-to-One NAT¾ List of Rules ¾ list of Rules 4.5.1.3 Multi-Nets NAT¾ Multi-Nets NAT Configuration procedure Application Example Network Requirements4.5.1.4 Virtual Server Status ¾ Virtual ServerProtocol 4.5.1.5 Port Triggering ¾ List of Rules¾ List of Rules 4.5.1.6 ALG¾ Port Triggering ¾ ALG 4.5.2.1 Setup4.5.2 Traffic Control Default Limit applies only for users that are not constrained by Bandwidth 4.5.2.2 Bandwidth Control ¾ Interface BandwidthSelect the data stream direction for the entry. The direction of arrowhead ¾ Bandwidth Control Rule¾ List of Rules 4.5.3 Session Limit 4.5.3.1 Session Limit4.5.4.1 Configuration 4.5.4 Load Balance4.5.3.2 Session List ¾ Session Limit4.5.4.2 Policy Routing ¾ List of Rules 4.5.4.3 Link Backup¾ General ¾ General 4.5.4.4 Protocol ¾ List of Rules4.5.5 Routing 4.5.5.1 Static Route¾ Protocol ¾ List of Protocol¾ Static Route ¾ List of RulesConfiguration procedure Application Example Network Requirements4.6.1.1 IP-MAC Binding 4.6 Firewall4.6.1 Anti ARP Spoofing ¾ IP-MAC Binding ¾ GeneralIP Address Status4.6.1.2 ARP Scanning ¾ List of Rules4.6.2 Attack Defense 4.6.1.3 ARP List¾ General Figure 4-41 Attack DefenseThe following items are displayed on this screen 4.6.3 MAC Filtering ¾ MAC FilteringEnable Attack Packet Anomaly4.6.4 Access Control 4.6.4.1 URL Filtering¾ List of Rules ¾ GeneralConfiguration Procedure ¾ URL Filtering Rule¾ List of Rules Application Example Network Requirements4.6.4.3 Access Rules 4.6.4.2 Web FilteringPolicy ¾ Access RulesService ¾ List of Rules 4.6.4.4 Service ¾ Service4.6.5.1 Control Rules ¾ List of Service4.6.5 App Control 4.6.5.2 Database ¾ Control Rules¾ General ¾ List of Rules4.7.1.1 General 4.7 Services4.7.1 PPPoE Server PPPoE Server Specify whether to enable the PPPoE Server function ¾ General4.7.1.2 IP Address Pool 4.7.1.3 Account¾ IP Address Pool ¾ List of IP PoolIP Address Pool Max Sessions ¾ AccountAccount Name Password IP Address Assigned Mode Static IP Address ¾ List of Account is 48. If Enable Advanced Account Features is not selected, the4.7.1.4 Exceptional IP ¾ List of Account 4.7.1.5 List of Account¾ Exceptional IP Interval 4.7.2 E-Bulletin¾ General 4.7.3 Dynamic DNS ¾ E-Bulletin¾ List of E-Bulletin Tips4.7.3.1 DynDNS ¾ List of DynDNS Account 4.7.3.2 No-IP¾ Dyndns DDNS ¾ No-IP DDNS ¾ List of No-IP Account4.7.3.3 PeanutHull ¾ PeanutHull DDNS4.7.3.4 Comexe ¾ List of PeanutHull Account¾ List of Comexe Account 4.7.4 UPnP¾ Comexe DDNS ¾ General ¾ List of UPnP MappingOn this page you can configure UPnP service 4.8 Maintenance 4.8.1 Admin Setup4.8.1.1 Administrator ¾ AdministratorApplication Example Network Requirements 4.8.1.2 Login Parameter¾ General Configuration Procedure 4.8.1.3 Remote Management¾ Remote Management 4.8.2.1 Factory Defaults 4.8.2 Management4.8.2.2 Export and Import ¾ List of Subnet4.8.2.3 Reboot 4.8.2.4 Firmware Upgrade¾ Configuration Version ¾ Export¾ Interface Traffic Statistics 4.8.3 Statistics4.8.3.1 Interface Traffic Statistics 4.8.3.2 IP Traffic Statistics ¾ Advanced WAN Information¾ Traffic Statistics ¾ IP Traffic Statistics4.8.4 Diagnostics 4.8.4.1 Diagnostics4.8.4.2 Online Detection ¾ Ping¾ Tracert ¾ General4.8.5 Time 4.8.5.1 Time¾ List of WAN status ¾ Current Time¾ Config 4.8.5.2 Daylight Saving Time¾ Daylight Saving TimeDST State ¾ Daylight Saving TimeDST Config4.8.6 Logs ¾ List of Logs Level¾ Config SeverityAppendix A Hardware Specifications PowerPorts Transmission MediumAppendix B FAQ 4. Make sure that the NAT DMZ service is disabled Description Appendix C GlossaryGlossary Description for services such as IPSec that require keys. Before any IPSecGlossary Glossary DescriptionTelnet is used for remote terminal connection, enabling users to GlossaryDescription