Manuals / TP-Link / Computer Equipment / Network Router

TP-Link 1910010933 manual Quick Setup, Network, 4.3.1 WAN, 4.3.1.2 WAN1, ¾ WAN Mode

Models: 1910010933

1 124

Download 124 pages 9.3 Kb

Page 23

4.2 Quick Setup

4.2 Quick Setup

Please refer to the Chapter 3 Quick Installation Guide.

4.3 Network

4.3.1 WAN

4.3.1.1WAN Mode

TL-R480T+ provides four available WAN ports. You can set the number of WAN ports on this page.

Choose the menu Network→WAN→WAN Mode to load the following page.

Figure 4-2 WAN Mode

¾WAN Mode

WAN Ports:Select the total number of WAN ports you prefer to use. And the router will adjust the physical ports accordingly, which can be illustrated on the following port sketch.

Note:

●By default, TL-R480T+ is set to work in the mode of dual WAN ports.

●Any change to the number of WAN ports may lead to a loss of current configurations. Please be sure to backup your configurations in advance.

4.3.1.2WAN1

TL-R480T+ provides the following six Internet connection types: Static IP, Dynamic IP, PPPoE/Russian PPPoE, L2TP/Russian L2TP, PPTP/Russian PPTP and BigPond. To configure the WAN, please first select the type of Internet connection provided by your ISP (Internet Service Provider).

-18-

Image 23

TP-Link 1910010933 manual Quick Setup, Network, 4.3.1 WAN, 4.3.1.2 WAN1, ¾ WAN Mode

Contents

REV6.0.0 1910010933 TL-R480T+ Load Balance Broadband RouterCE Mark Warning COPYRIGHT & TRADEMARKSFCC STATEMENT 安全諮詢及注意事項 Safety InformationChapter 1 About this Guide CONTENTSChapter 3 Quick Installation Guide Chapter 4 ConfigurationAppendix B Hardware SpecificationsGlossary Appendix APackage Contents 1.2 Conventions SymbolChapter 1 About this Guide 1.1 Intended ReadersAppendix C Glossary Appendix B FAQProvides the possible solutions to the problems that may occur during the installation and operation of the router2.1 Overview of the Router z Powerful Data Processing Capabilityz Powerful Firewall Chapter 2 IntroductionBasic Functions 2.2 Featuresz Easy-to-use Hardwarez LEDs 2.3 Appearance2.3.1 Front Panel Securityz Interface Description z Reset buttonz AC Power Receptacle 2.3.2 Rear Panel3.1 Configure PC Chapter 3 Quick Installation GuidePage Page Is the connection between your PC and the router correct? 3.2 LoginIs the TCP/IP configuration for your PC correct? Figure 3-9 WAN Mode Figure 3-8 Quick SetupFigure 3-11 WAN Connection Type Figure 3-10 WAN PortFigure 3-12 WAN Connection Type - PPPoE Figure 3-13 WAN Connection Type - PPPoE ConnectingIf you have difficulty in this process, please contact your ISP Figure 3-14 WAN Connection Type - Dynamic IPFigure 3-15 WAN Connection Type - Static IP Figure 3-17 Configuration Completed Figure 3-16 WAN Connection Type - Static IP Connecting4.1 Status Chapter 4 Configuration4.3 Network 4.2 Quick Setup4.3.1.1 WAN Mode ¾ WAN ModeTips 1 Static IP¾ Static IP Choose the menu Network→WAN→WAN1 to load the configuration pageSecondary DNS 2 Dynamic IPDefault Gateway Primary DNS¾ Dynamic IP z “Connected” indicates that the router has successfully obtained ¾ Dynamic IP StatusSelect this option to enter the DNS Domain Name Server address Figure 4-5 WAN - PPPoE 3 PPPoEPrimary DNS Displays the IP address of your ISP’s Primary DNS Secondary DNS Displays the IP address of your ISP’s Secondary DNSEnter the Account Name provided by your ISP. If you are not clear ¾ PPPoE Settingson. The connection can be re-established automatically when it 576-1492. The default MTU is 1480. You are recommended to keepDynamic IP is selected, the obtained subnet address of WAN port is Here allows you to configure the secondary connection. Dynamic IPmanually terminated or the router gets no response from ¾ PPPoE StatusFigure 4-6 WAN - L2TP 4 L2TPEnter the Account Name provided by your ISP. If you are not ¾ L2TP SettingsSubnet Mask ¾ L2TP StatusDefault Gateway IP AddressDisplays the IP address of your ISP’s Secondary DNS 5 PPTPConnection Type ¾ PPTP SettingsPassword Active ModeUpstream Bandwidth ¾ PPTP StatusDefault Gateway Subnet Mask6 BigPond ¾ BigPond Settingsbeen ¾ BigPond Status¾ LAN 4.3.2 LAN4.3.2.1 LAN 4.3.2.2 DHCP ¾ DHCP Settings4.3.2.4 DHCP Reservation 4.3.2.3 DHCP ClientActivate or Inactivate the corresponding entry ¾ DHCP Reservation¾ List of Reserved Address ¾ MAC Address 4.3.3 MAC AddressSet the MAC Address for LAN port Set the MAC Address for WAN port4.3.4.1 Statistics 4.3.4 Switch¾ Statistics 4.3.4.2 Port Mirror¾ Port Mirror ¾ GeneralTips 4.3.4.3 Rate ControlApplication Example ¾ Rate Control 4.3.4.4 Port Config4.3.4.5 Port Status ¾ Port ConfigTips 4.4 User Group4.3.4.6 Port VLAN ¾ Port VLAN¾ List of Group ¾ Group Config4.4.1 Group 4.4.2 User¾ List of User ¾ User Config4.4.3 View 4.5.1 NAT 4.5.1.1 NAT Setup¾ View Config 4.5 Advanced¾ NAT-DMZ 4.5.1.2 One-to-One NAT¾ NAPT Activate or inactivate the entry ¾ One-to-One NAT¾ List of Rules ¾ list of Rules 4.5.1.3 Multi-Nets NAT¾ Multi-Nets NAT Application Example Network Requirements Configuration procedure4.5.1.4 Virtual Server Status ¾ Virtual ServerProtocol ¾ List of Rules 4.5.1.5 Port Triggering¾ List of Rules 4.5.1.6 ALG¾ Port Triggering ¾ ALG 4.5.2.1 Setup4.5.2 Traffic Control Default Limit applies only for users that are not constrained by Bandwidth ¾ Interface Bandwidth 4.5.2.2 Bandwidth ControlSelect the data stream direction for the entry. The direction of arrowhead ¾ Bandwidth Control Rule¾ List of Rules 4.5.3.1 Session Limit 4.5.3 Session Limit¾ Session Limit 4.5.4.1 Configuration4.5.4 Load Balance 4.5.3.2 Session List4.5.4.2 Policy Routing ¾ List of Rules 4.5.4.3 Link Backup¾ General ¾ General ¾ List of Rules 4.5.4.4 Protocol¾ List of Protocol 4.5.5 Routing4.5.5.1 Static Route ¾ Protocol¾ List of Rules ¾ Static RouteApplication Example Network Requirements Configuration procedure4.6.1.1 IP-MAC Binding 4.6 Firewall4.6.1 Anti ARP Spoofing Status ¾ IP-MAC Binding¾ General IP Address¾ List of Rules 4.6.1.2 ARP Scanning4.6.1.3 ARP List 4.6.2 Attack Defense¾ General Figure 4-41 Attack DefenseThe following items are displayed on this screen Packet Anomaly 4.6.3 MAC Filtering¾ MAC Filtering Enable Attack¾ General 4.6.4 Access Control4.6.4.1 URL Filtering ¾ List of RulesApplication Example Network Requirements Configuration Procedure¾ URL Filtering Rule ¾ List of Rules4.6.4.2 Web Filtering 4.6.4.3 Access RulesPolicy ¾ Access RulesService ¾ List of Rules ¾ Service 4.6.4.4 Service4.6.5.1 Control Rules ¾ List of Service4.6.5 App Control ¾ List of Rules 4.6.5.2 Database¾ Control Rules ¾ General4.7.1.1 General 4.7 Services4.7.1 PPPoE Server ¾ General PPPoE Server Specify whether to enable the PPPoE Server function¾ List of IP Pool 4.7.1.2 IP Address Pool4.7.1.3 Account ¾ IP Address PoolIP Address Pool Max Sessions ¾ AccountAccount Name Password IP Address Assigned Mode Static IP Address ¾ List of Account is 48. If Enable Advanced Account Features is not selected, the4.7.1.4 Exceptional IP ¾ List of Account 4.7.1.5 List of Account¾ Exceptional IP Interval 4.7.2 E-Bulletin¾ General Tips 4.7.3 Dynamic DNS¾ E-Bulletin ¾ List of E-Bulletin4.7.3.1 DynDNS ¾ List of DynDNS Account 4.7.3.2 No-IP¾ Dyndns DDNS ¾ List of No-IP Account ¾ No-IP DDNS¾ PeanutHull DDNS 4.7.3.3 PeanutHull¾ List of PeanutHull Account 4.7.3.4 Comexe¾ List of Comexe Account 4.7.4 UPnP¾ Comexe DDNS ¾ General ¾ List of UPnP MappingOn this page you can configure UPnP service ¾ Administrator 4.8 Maintenance4.8.1 Admin Setup 4.8.1.1 AdministratorApplication Example Network Requirements 4.8.1.2 Login Parameter¾ General Configuration Procedure 4.8.1.3 Remote Management¾ Remote Management ¾ List of Subnet 4.8.2.1 Factory Defaults4.8.2 Management 4.8.2.2 Export and Import¾ Export 4.8.2.3 Reboot4.8.2.4 Firmware Upgrade ¾ Configuration Version¾ Interface Traffic Statistics 4.8.3 Statistics4.8.3.1 Interface Traffic Statistics ¾ IP Traffic Statistics 4.8.3.2 IP Traffic Statistics¾ Advanced WAN Information ¾ Traffic Statistics4.8.4.1 Diagnostics 4.8.4 Diagnostics¾ General 4.8.4.2 Online Detection¾ Ping ¾ Tracert¾ Current Time 4.8.5 Time4.8.5.1 Time ¾ List of WAN status4.8.5.2 Daylight Saving Time ¾ Config¾ Daylight Saving TimeDST State ¾ Daylight Saving TimeDST Config4.8.6 Logs Severity ¾ List of LogsLevel ¾ ConfigTransmission Medium Appendix A Hardware SpecificationsPower PortsAppendix B FAQ 4. Make sure that the NAT DMZ service is disabled Description Appendix C GlossaryGlossary Description for services such as IPSec that require keys. Before any IPSecGlossary Description GlossaryTelnet is used for remote terminal connection, enabling users to GlossaryDescription