Manuals / TP-Link / Computer Equipment / Network Router

TP-Link 1910010933 manual Dynamic DNS, ¾ E-Bulletin, ¾ List of E-Bulletin, Tips

Models: 1910010933

1 124

Download 124 pages 9.3 Kb

Page 97

¾ E-Bulletin

Enable Logs:	Specify whether to log the E-Bulletin.
¾ E-Bulletin
Title:	Enter a title for the bulletin.
Content:	Enter the content of the bulletin.
Object:	Select the object of this bulletin. Options include:
	z ANY: The bulletin will be released to all the users and the PCs on the
	LAN.
	z Group: The bulletin will be released to the users in the selected group.
	You can click <	> button to add a group to the selected group
	and click <	> to remove a group from the selected group.
	Group is created on User Group→Group page.
Effective Time:	Specify the effective time for the bulletin. Only one bulletin can be set for
	the object at the same time.
Publisher:	Enter the name of the bulletin's publisher.
Description:	Enter the description for the bulletin.
Status:	Activate or inactivate the entry.

¾List of E-Bulletin

In this table, you can view the existing bulletins and edit them by the Action button.

The No.1 entry in Figure 4-54indicates: this bulletin is released by the administrator, and it is released to the Group1 from 8am to 20pm on Thursday and Friday every a bulletin interval. (the interval in the figure is 30 min). This entry is enabled.

Tips:

For the configuration for groups and users, please refer to the User Group section.

4.7.3 Dynamic DNS

DDNS (Dynamic DNS) service allows you to assign a fixed domain name to a dynamic WAN IP address, which enables the Internet hosts to access the router or the hosts in LAN using the domain names.

-92-

Image 97

TP-Link 1910010933 manual Dynamic DNS, ¾ E-Bulletin, ¾ List of E-Bulletin, Tips

Contents

REV6.0.0 1910010933 TL-R480T+ Load Balance Broadband RouterFCC STATEMENT COPYRIGHT & TRADEMARKSCE Mark Warning 安全諮詢及注意事項 Safety InformationChapter 3 Quick Installation Guide CONTENTSChapter 4 Configuration Chapter 1 About this GuideGlossary Hardware SpecificationsAppendix A Appendix BPackage Contents Chapter 1 About this Guide Symbol1.1 Intended Readers 1.2 ConventionsProvides the possible solutions to the problems that may occur during Appendix B FAQthe installation and operation of the router Appendix C Glossaryz Powerful Firewall z Powerful Data Processing CapabilityChapter 2 Introduction 2.1 Overview of the Routerz Easy-to-use 2.2 FeaturesHardware Basic Functions2.3.1 Front Panel 2.3 AppearanceSecurity z LEDsz AC Power Receptacle z Reset button2.3.2 Rear Panel z Interface Description3.1 Configure PC Chapter 3 Quick Installation GuidePage Page Is the TCP/IP configuration for your PC correct? 3.2 LoginIs the connection between your PC and the router correct? Figure 3-9 WAN Mode Figure 3-8 Quick SetupFigure 3-11 WAN Connection Type Figure 3-10 WAN PortFigure 3-12 WAN Connection Type - PPPoE Figure 3-13 WAN Connection Type - PPPoE ConnectingFigure 3-15 WAN Connection Type - Static IP Figure 3-14 WAN Connection Type - Dynamic IPIf you have difficulty in this process, please contact your ISP Figure 3-17 Configuration Completed Figure 3-16 WAN Connection Type - Static IP Connecting4.1 Status Chapter 4 Configuration4.3.1.1 WAN Mode 4.2 Quick Setup¾ WAN Mode 4.3 Network¾ Static IP 1 Static IPChoose the menu Network→WAN→WAN1 to load the configuration page TipsDefault Gateway 2 Dynamic IPPrimary DNS Secondary DNS¾ Dynamic IP Select this option to enter the DNS Domain Name Server address ¾ Dynamic IP Statusz “Connected” indicates that the router has successfully obtained Primary DNS Displays the IP address of your ISP’s Primary DNS 3 PPPoESecondary DNS Displays the IP address of your ISP’s Secondary DNS Figure 4-5 WAN - PPPoEon. The connection can be re-established automatically when it ¾ PPPoE Settings576-1492. The default MTU is 1480. You are recommended to keep Enter the Account Name provided by your ISP. If you are not clearDynamic IP is selected, the obtained subnet address of WAN port is Here allows you to configure the secondary connection. Dynamic IPmanually terminated or the router gets no response from ¾ PPPoE StatusFigure 4-6 WAN - L2TP 4 L2TPEnter the Account Name provided by your ISP. If you are not ¾ L2TP SettingsDefault Gateway ¾ L2TP StatusIP Address Subnet MaskDisplays the IP address of your ISP’s Secondary DNS 5 PPTPPassword ¾ PPTP SettingsActive Mode Connection TypeDefault Gateway ¾ PPTP StatusSubnet Mask Upstream Bandwidth6 BigPond ¾ BigPond Settingsbeen ¾ BigPond Status4.3.2.1 LAN 4.3.2 LAN¾ LAN 4.3.2.2 DHCP ¾ DHCP Settings4.3.2.4 DHCP Reservation 4.3.2.3 DHCP Client¾ List of Reserved Address ¾ DHCP ReservationActivate or Inactivate the corresponding entry Set the MAC Address for LAN port 4.3.3 MAC AddressSet the MAC Address for WAN port ¾ MAC Address4.3.4.1 Statistics 4.3.4 Switch¾ Statistics 4.3.4.2 Port Mirror¾ Port Mirror ¾ GeneralApplication Example 4.3.4.3 Rate ControlTips ¾ Rate Control 4.3.4.4 Port Config4.3.4.5 Port Status ¾ Port Config4.3.4.6 Port VLAN 4.4 User Group¾ Port VLAN Tips4.4.1 Group ¾ Group Config4.4.2 User ¾ List of Group4.4.3 View ¾ User Config¾ List of User ¾ View Config 4.5.1.1 NAT Setup4.5 Advanced 4.5.1 NAT¾ NAPT 4.5.1.2 One-to-One NAT¾ NAT-DMZ ¾ List of Rules ¾ One-to-One NATActivate or inactivate the entry ¾ Multi-Nets NAT 4.5.1.3 Multi-Nets NAT¾ list of Rules Application Example Network Requirements Configuration procedure4.5.1.4 Virtual Server Protocol ¾ Virtual ServerStatus ¾ List of Rules 4.5.1.5 Port Triggering¾ Port Triggering 4.5.1.6 ALG¾ List of Rules 4.5.2 Traffic Control 4.5.2.1 Setup¾ ALG Default Limit applies only for users that are not constrained by Bandwidth ¾ Interface Bandwidth 4.5.2.2 Bandwidth Control¾ List of Rules ¾ Bandwidth Control RuleSelect the data stream direction for the entry. The direction of arrowhead 4.5.3.1 Session Limit 4.5.3 Session Limit4.5.4 Load Balance 4.5.4.1 Configuration4.5.3.2 Session List ¾ Session Limit4.5.4.2 Policy Routing ¾ General 4.5.4.3 Link Backup¾ List of Rules ¾ General ¾ List of Rules 4.5.4.4 Protocol4.5.5.1 Static Route 4.5.5 Routing¾ Protocol ¾ List of Protocol¾ List of Rules ¾ Static RouteApplication Example Network Requirements Configuration procedure4.6.1 Anti ARP Spoofing 4.6 Firewall4.6.1.1 IP-MAC Binding ¾ General ¾ IP-MAC BindingIP Address Status¾ List of Rules 4.6.1.2 ARP Scanning4.6.1.3 ARP List 4.6.2 Attack DefenseThe following items are displayed on this screen Figure 4-41 Attack Defense¾ General ¾ MAC Filtering 4.6.3 MAC FilteringEnable Attack Packet Anomaly4.6.4.1 URL Filtering 4.6.4 Access Control¾ List of Rules ¾ General¾ URL Filtering Rule Configuration Procedure¾ List of Rules Application Example Network Requirements4.6.4.2 Web Filtering 4.6.4.3 Access RulesService ¾ Access RulesPolicy ¾ List of Rules ¾ Service 4.6.4.4 Service4.6.5 App Control ¾ List of Service4.6.5.1 Control Rules ¾ Control Rules 4.6.5.2 Database¾ General ¾ List of Rules4.7.1 PPPoE Server 4.7 Services4.7.1.1 General ¾ General PPPoE Server Specify whether to enable the PPPoE Server function4.7.1.3 Account 4.7.1.2 IP Address Pool¾ IP Address Pool ¾ List of IP PoolAccount Name Password IP Address Assigned Mode Static IP Address ¾ AccountIP Address Pool Max Sessions 4.7.1.4 Exceptional IP is 48. If Enable Advanced Account Features is not selected, the¾ List of Account ¾ Exceptional IP 4.7.1.5 List of Account¾ List of Account ¾ General 4.7.2 E-BulletinInterval ¾ E-Bulletin 4.7.3 Dynamic DNS¾ List of E-Bulletin Tips4.7.3.1 DynDNS ¾ Dyndns DDNS 4.7.3.2 No-IP¾ List of DynDNS Account ¾ List of No-IP Account ¾ No-IP DDNS¾ PeanutHull DDNS 4.7.3.3 PeanutHull¾ List of PeanutHull Account 4.7.3.4 Comexe¾ Comexe DDNS 4.7.4 UPnP¾ List of Comexe Account On this page you can configure UPnP service ¾ List of UPnP Mapping¾ General 4.8.1 Admin Setup 4.8 Maintenance4.8.1.1 Administrator ¾ Administrator¾ General 4.8.1.2 Login ParameterApplication Example Network Requirements ¾ Remote Management 4.8.1.3 Remote ManagementConfiguration Procedure 4.8.2 Management 4.8.2.1 Factory Defaults4.8.2.2 Export and Import ¾ List of Subnet4.8.2.4 Firmware Upgrade 4.8.2.3 Reboot¾ Configuration Version ¾ Export4.8.3.1 Interface Traffic Statistics 4.8.3 Statistics¾ Interface Traffic Statistics ¾ Advanced WAN Information 4.8.3.2 IP Traffic Statistics¾ Traffic Statistics ¾ IP Traffic Statistics4.8.4.1 Diagnostics 4.8.4 Diagnostics¾ Ping 4.8.4.2 Online Detection¾ Tracert ¾ General4.8.5.1 Time 4.8.5 Time¾ List of WAN status ¾ Current Time4.8.5.2 Daylight Saving Time ¾ Config4.8.6 Logs ¾ Daylight Saving TimeDST Config¾ Daylight Saving TimeDST State Level ¾ List of Logs¾ Config SeverityPower Appendix A Hardware SpecificationsPorts Transmission MediumAppendix B FAQ 4. Make sure that the NAT DMZ service is disabled Glossary Appendix C GlossaryDescription Glossary for services such as IPSec that require keys. Before any IPSecDescription Description GlossaryDescription GlossaryTelnet is used for remote terminal connection, enabling users to