Manuals / TP-Link / Computer Equipment / Network Router

TP-Link 1910010933 manual Bandwidth Control, ¾ Interface Bandwidth

Models: 1910010933

1 124

Download 124 pages 9.3 Kb

Page 65

¾Interface Bandwidth

¾Interface Bandwidth

Interface:	Displays the current enabled WAN port(s). The Total bandwidth is equal to
	the sum of bandwidth of the enabled WAN ports.
Upstream	Displays the bandwidth of each WAN port for transmitting data. The
Bandwidth:	Upstream Bandwidth of WAN port can be configured on WAN page.
Downstream	Displays the bandwidth of each WAN port for receiving data. The
Bandwidth:	Downstream Bandwidth of WAN port can be configured on WAN page.

Note:

●The Upstream/Downstream Bandwidth of WAN port you set must not be more than the bandwidth provided by ISP. Otherwise the Traffic Control will be invalid.

●If there are data flowing into the router from interface A and out from interface B while the downstream bandwidth of A is different from the upstream bandwidth of B, then the smaller one should be considered as the effective bandwidth, and vise versa.

●Click the <View IP Traffic Statistics> button to jump to IP Traffic Statistics page.

4.5.2.2Bandwidth Control

On this page, you can configure the Bandwidth Control function.

Choose the menu Advanced→Traffic Control→Bandwidth Control to load the following page.

Figure 4-30 Bandwidth Control

The following items are displayed on this screen:

-60-

Image 65

TP-Link 1910010933 manual Bandwidth Control, ¾ Interface Bandwidth

Contents

REV6.0.0 1910010933 TL-R480T+ Load Balance Broadband RouterCE Mark Warning COPYRIGHT & TRADEMARKSFCC STATEMENT 安全諮詢及注意事項 Safety InformationChapter 3 Quick Installation Guide CONTENTSChapter 4 Configuration Chapter 1 About this GuideGlossary Hardware SpecificationsAppendix A Appendix BPackage Contents Chapter 1 About this Guide Symbol1.1 Intended Readers 1.2 ConventionsProvides the possible solutions to the problems that may occur during Appendix B FAQthe installation and operation of the router Appendix C Glossaryz Powerful Firewall z Powerful Data Processing CapabilityChapter 2 Introduction 2.1 Overview of the Routerz Easy-to-use 2.2 FeaturesHardware Basic Functions2.3.1 Front Panel 2.3 AppearanceSecurity z LEDsz AC Power Receptacle z Reset button2.3.2 Rear Panel z Interface Description3.1 Configure PC Chapter 3 Quick Installation GuidePage Page Is the connection between your PC and the router correct? 3.2 LoginIs the TCP/IP configuration for your PC correct? Figure 3-9 WAN Mode Figure 3-8 Quick SetupFigure 3-11 WAN Connection Type Figure 3-10 WAN PortFigure 3-12 WAN Connection Type - PPPoE Figure 3-13 WAN Connection Type - PPPoE ConnectingIf you have difficulty in this process, please contact your ISP Figure 3-14 WAN Connection Type - Dynamic IPFigure 3-15 WAN Connection Type - Static IP Figure 3-17 Configuration Completed Figure 3-16 WAN Connection Type - Static IP Connecting4.1 Status Chapter 4 Configuration4.3.1.1 WAN Mode 4.2 Quick Setup¾ WAN Mode 4.3 Network¾ Static IP 1 Static IPChoose the menu Network→WAN→WAN1 to load the configuration page TipsDefault Gateway 2 Dynamic IPPrimary DNS Secondary DNS¾ Dynamic IP z “Connected” indicates that the router has successfully obtained ¾ Dynamic IP StatusSelect this option to enter the DNS Domain Name Server address Primary DNS Displays the IP address of your ISP’s Primary DNS 3 PPPoESecondary DNS Displays the IP address of your ISP’s Secondary DNS Figure 4-5 WAN - PPPoEon. The connection can be re-established automatically when it ¾ PPPoE Settings576-1492. The default MTU is 1480. You are recommended to keep Enter the Account Name provided by your ISP. If you are not clearDynamic IP is selected, the obtained subnet address of WAN port is Here allows you to configure the secondary connection. Dynamic IPmanually terminated or the router gets no response from ¾ PPPoE StatusFigure 4-6 WAN - L2TP 4 L2TPEnter the Account Name provided by your ISP. If you are not ¾ L2TP SettingsDefault Gateway ¾ L2TP StatusIP Address Subnet MaskDisplays the IP address of your ISP’s Secondary DNS 5 PPTPPassword ¾ PPTP SettingsActive Mode Connection TypeDefault Gateway ¾ PPTP StatusSubnet Mask Upstream Bandwidth6 BigPond ¾ BigPond Settingsbeen ¾ BigPond Status¾ LAN 4.3.2 LAN4.3.2.1 LAN 4.3.2.2 DHCP ¾ DHCP Settings4.3.2.4 DHCP Reservation 4.3.2.3 DHCP ClientActivate or Inactivate the corresponding entry ¾ DHCP Reservation¾ List of Reserved Address Set the MAC Address for LAN port 4.3.3 MAC AddressSet the MAC Address for WAN port ¾ MAC Address4.3.4.1 Statistics 4.3.4 Switch¾ Statistics 4.3.4.2 Port Mirror¾ Port Mirror ¾ GeneralTips 4.3.4.3 Rate ControlApplication Example ¾ Rate Control 4.3.4.4 Port Config4.3.4.5 Port Status ¾ Port Config4.3.4.6 Port VLAN 4.4 User Group¾ Port VLAN Tips4.4.1 Group ¾ Group Config4.4.2 User ¾ List of Group¾ List of User ¾ User Config4.4.3 View ¾ View Config 4.5.1.1 NAT Setup4.5 Advanced 4.5.1 NAT¾ NAT-DMZ 4.5.1.2 One-to-One NAT¾ NAPT Activate or inactivate the entry ¾ One-to-One NAT¾ List of Rules ¾ list of Rules 4.5.1.3 Multi-Nets NAT¾ Multi-Nets NAT Application Example Network Requirements Configuration procedure4.5.1.4 Virtual Server Status ¾ Virtual ServerProtocol ¾ List of Rules 4.5.1.5 Port Triggering¾ List of Rules 4.5.1.6 ALG¾ Port Triggering ¾ ALG 4.5.2.1 Setup4.5.2 Traffic Control Default Limit applies only for users that are not constrained by Bandwidth ¾ Interface Bandwidth 4.5.2.2 Bandwidth ControlSelect the data stream direction for the entry. The direction of arrowhead ¾ Bandwidth Control Rule¾ List of Rules 4.5.3.1 Session Limit 4.5.3 Session Limit4.5.4 Load Balance 4.5.4.1 Configuration4.5.3.2 Session List ¾ Session Limit4.5.4.2 Policy Routing ¾ List of Rules 4.5.4.3 Link Backup¾ General ¾ General ¾ List of Rules 4.5.4.4 Protocol4.5.5.1 Static Route 4.5.5 Routing¾ Protocol ¾ List of Protocol¾ List of Rules ¾ Static RouteApplication Example Network Requirements Configuration procedure4.6.1.1 IP-MAC Binding 4.6 Firewall4.6.1 Anti ARP Spoofing ¾ General ¾ IP-MAC BindingIP Address Status¾ List of Rules 4.6.1.2 ARP Scanning4.6.1.3 ARP List 4.6.2 Attack Defense¾ General Figure 4-41 Attack DefenseThe following items are displayed on this screen ¾ MAC Filtering 4.6.3 MAC FilteringEnable Attack Packet Anomaly4.6.4.1 URL Filtering 4.6.4 Access Control¾ List of Rules ¾ General¾ URL Filtering Rule Configuration Procedure¾ List of Rules Application Example Network Requirements4.6.4.2 Web Filtering 4.6.4.3 Access RulesPolicy ¾ Access RulesService ¾ List of Rules ¾ Service 4.6.4.4 Service4.6.5.1 Control Rules ¾ List of Service4.6.5 App Control ¾ Control Rules 4.6.5.2 Database¾ General ¾ List of Rules4.7.1.1 General 4.7 Services4.7.1 PPPoE Server ¾ General PPPoE Server Specify whether to enable the PPPoE Server function4.7.1.3 Account 4.7.1.2 IP Address Pool¾ IP Address Pool ¾ List of IP PoolIP Address Pool Max Sessions ¾ AccountAccount Name Password IP Address Assigned Mode Static IP Address ¾ List of Account is 48. If Enable Advanced Account Features is not selected, the4.7.1.4 Exceptional IP ¾ List of Account 4.7.1.5 List of Account¾ Exceptional IP Interval 4.7.2 E-Bulletin¾ General ¾ E-Bulletin 4.7.3 Dynamic DNS¾ List of E-Bulletin Tips4.7.3.1 DynDNS ¾ List of DynDNS Account 4.7.3.2 No-IP¾ Dyndns DDNS ¾ List of No-IP Account ¾ No-IP DDNS¾ PeanutHull DDNS 4.7.3.3 PeanutHull¾ List of PeanutHull Account 4.7.3.4 Comexe¾ List of Comexe Account 4.7.4 UPnP¾ Comexe DDNS ¾ General ¾ List of UPnP MappingOn this page you can configure UPnP service 4.8.1 Admin Setup 4.8 Maintenance4.8.1.1 Administrator ¾ AdministratorApplication Example Network Requirements 4.8.1.2 Login Parameter¾ General Configuration Procedure 4.8.1.3 Remote Management¾ Remote Management 4.8.2 Management 4.8.2.1 Factory Defaults4.8.2.2 Export and Import ¾ List of Subnet4.8.2.4 Firmware Upgrade 4.8.2.3 Reboot¾ Configuration Version ¾ Export¾ Interface Traffic Statistics 4.8.3 Statistics4.8.3.1 Interface Traffic Statistics ¾ Advanced WAN Information 4.8.3.2 IP Traffic Statistics¾ Traffic Statistics ¾ IP Traffic Statistics4.8.4.1 Diagnostics 4.8.4 Diagnostics¾ Ping 4.8.4.2 Online Detection¾ Tracert ¾ General4.8.5.1 Time 4.8.5 Time¾ List of WAN status ¾ Current Time4.8.5.2 Daylight Saving Time ¾ Config¾ Daylight Saving TimeDST State ¾ Daylight Saving TimeDST Config4.8.6 Logs Level ¾ List of Logs¾ Config SeverityPower Appendix A Hardware SpecificationsPorts Transmission MediumAppendix B FAQ 4. Make sure that the NAT DMZ service is disabled Description Appendix C GlossaryGlossary Description for services such as IPSec that require keys. Before any IPSecGlossary Description GlossaryTelnet is used for remote terminal connection, enabling users to GlossaryDescription