Hardware Setup

Before You Begin

General Safety Instructions

•Read all of these instructions. Save them for future reference.

•Follow all warnings and instructions marked on the device.

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide.

•This device is designed for IT Power Distribution systems with up to 230V phase-to-phase voltage.

•Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result.

•Do not use the device near water.

•Do not place the device near, or over, radiators or heat registers.

•The device cabinet is provided with slots and openings to allow for adequate ventilation. To ensure reliable operation, and to protect against overheating, these openings must never be blocked or covered.

•The device should never be placed on a soft surface (bed, sofa, rug, etc.), as this will block its ventilation openings. Likewise, the device should not be placed in a built in enclosure unless adequate ventilation has been provided.

•Never spill liquid of any kind on the device.

•Unplug the device from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

•The device should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.

•To prevent damage to your installation it is important that all devices are properly grounded.

•The device is equipped with a 3-wire grounding type plug. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not attempt to defeat the purpose of the grounding-type plug. Always follow your local/ national wiring codes.

•Do not allow anything to rest on the power cord or cables. Route the power cord and cables so that they cannot be stepped on or tripped over.

•If an extension cord is used with this device make sure that the total ampere rating of all products used on this cord does not exceed the extension cord ampere rating. Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.

•To help protect your system from sudden, transient increases and decreases in electrical power, it is recommended that you plug your devices into a Tripp Lite surge suppressor, line conditioner, or uninterruptible power supply (UPS).

•Position system cables and power cables carefully to ensure that nothing rests on any cables.

•When connecting or disconnecting power to hot-pluggable power supplies, observe the following guidelines:

•Install the power supply before connecting the power cable to the power supply.

•Unplug the power cable before removing the power supply.

• If the system has multiple sources of power, disconnect power from the system by unplugging all power cables from the power supplies.

•Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock.

•Do not attempt to service the device yourself. Refer all servicing to qualified service personnel.

•If the following conditions occur, unplug the device from the wall outlet and bring it to qualified service personnel for repair:

•The power cord or plug has become damaged or frayed.

•Liquid has been spilled into the device.

•The device has been exposed to rain or water.

•The device has been dropped, or the cabinet has been damaged.

•The device exhibits a distinct change in performance, indicating a need for service.

•The device does not operate normally when the operating instructions are followed.

•Only adjust those controls that are covered in the operating instructions. Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair.

•Do not connect the RJ11 connector marked “UPGRADE” to a public telecommunication network.

8

Page 7 Page 9
Page 8
Image 8
Tripp Lite B064-032-04-IP, B064-032-02-IP, B064-016-02-IP Hardware Setup, Before You Begin General Safety Instructions
Page 7 Page 9

B064-032-02-IP, B064-016-02-IP, B064-032-04-IP specifications

Tripp Lite is renowned for its high-quality connectivity solutions, and their line of IP-based KVM switches, including models B064-032-04-IP, B064-016-02-IP, and B064-032-02-IP, showcases exceptional features designed for professional environments. These devices are specifically engineered to facilitate seamless control and management of multiple servers or computers through a single console.

The Tripp Lite B064-032-04-IP provides comprehensive KVM switching capabilities, supporting up to 32 servers over IP. This model is perfect for large data centers or IT environments where remote access to multiple systems is necessary. It features a user-friendly web interface that simplifies management, allowing administrators to switch between and control connected systems with ease. Additionally, it includes robust security measures, such as HTTPS and SSH protocols, ensuring that unauthorized access is prevented.

On a smaller scale, the B064-016-02-IP and B064-032-02-IP models cater to different user needs. The B064-016-02-IP manages up to 16 servers and offers similar IP-based access, making it ideal for medium-sized businesses. It includes a built-in Cat5e/6 KVM switch that allows users to control multiple computers using a single keyboard, mouse, and monitor, significantly reducing the clutter of cables.

The B064-032-02-IP strikes a balance between the two, supporting 32 devices while maintaining a streamlined design. This model is particularly appealing for small to midsize organizations that require flexibility to grow without unnecessary complexity.

All three models are compatible with various operating systems and provide multiple connectivity options, including VGA and HDMI, to cater to diverse setups. They also support high-definition video resolutions, ensuring that users experience clear, crisp visuals.

In terms of reliability, these KVM switches are crafted using advanced components and adhere to stringent quality standards, enabling them to perform efficiently in demanding environments. With features like hot-plugging capability, users can add or remove servers without shutting down, ensuring minimal disruption to operations.

Collectively, the Tripp Lite B064 models offer a powerful and flexible solution for managing computers and servers in various settings, combining technology, security, and ease of use to meet the needs of modern IT infrastructures.
Top Page Image Contents