PROGRAM 6 – PROGRAM 7: elevation program will change automatically during the exercise).
a.Press the SPEED +
b.The time window will glitter. Use the ELEVATION + – or SPEED+
c.Press the Enter to confirm your setting value.
d.Distant window will glitter. Use the ELEVATION + – or SPEED+ – buttons to set up the desired distance to do the exercise.
e.Press the Enter to confirm your setting value.
f.Kcal window will glitter. Use the ELEVATION +
– or SPEED+ – buttons to set up the desired calories to be consumed.
g.Press the Enter to confirm your setting value.
h.Press Start to begin exercise.
NOTE:
1.If you would not like to select any special target to reach, just press Start to do the exercise.
2.If you would like to skip the target setting, press the enter key to next setting value and this function will count up.
3.If you set up more than one target, once reach
the first target, Press Start again and this value will continue to count down until reach your next target.
USER1 – 2
a.Press SPEED + - or ELEVATION + - button to enter your desired User setting program.
b.The time window will glitter. Use the ELEVATION + – or SPEED+ – buttons to set up the desired exercise time.
c.Press the Enter to confirm your setting value.
d.Distant window will glitter. Use the ELEVATION + – or SPEED+ – buttons to set up the desired distance to do the exercise.
e.Press the Enter to confirm your setting value.
f.Kcal window will glitter. Use the ELEVATION +
– or SPEED+ – buttons to set up the desired calories to be consumed.
g.Press the Enter to confirm your setting value.
h.The SPEED and ELEVATION windows will glitter. Press SPEED+ or
i.Press Enter to confirm the first column.
j.Follow h points to finish the user setting profile. Total profile setting is 20 times. (20 columns)
k.Press Start to begin exercise.
NOTE:
1.If you would not like to select any special target to reach, just press Start to do the exercise.
2.If you would like to skip the target setting, press the enter key to next setting value and this function will count up.
3.If you set up more than one target, once reach
the first target, Press Start again and this value will continue to count down until reach your next target.
ENGINEERING MODE
1.during the power ON position, first hold the SELECT button then press the ENTER button
O W N E R ' S M A N U A L • T 1 0
together to enter the Engineering Mode
2.Speed window shows software version, Time window shows year, Distance window shows date.
3.Press ENTER button window shows LDU version. It is software version.
4.Press ENTER button window shows ISP version. It is software version.
5.Press ENTER button enter KM/MILE switch mode,
1 means KM, 0 means MILE
Press SPEED + - or ELEVATION + - to select KM or MILE.
6.Press ENTER button window shows total distance.
7.Press ENTER button window shows total hour.
8.Press ENTER button goes back to ON position.
MAINTENANCE
The equipment is safe to use only when periodically maintained and inspected for faults and wear.
CAUTION! Do not attempt any servicing or adjustment other than those described in this manual. Any other servicing must be performed by an authorized service representative. Check the tightness of all fixing screws once a year. Do not overtighten.
LUBRICATING THE RUNNING DECK
Lubrication is the most important service activity for the treadmill. This is absolutely essential, if the friction of the running deck increases noticeably or the motor begins to heat up; increased friction is indicated by jerky movement of the belt. Insufficient lubrication will cause the belt, running deck and motor to wear out and break. The need for re- lubrication depends to a great extent on the running styles and weight of the user: heavy user weight and slow speed put particular strain on the device and therefore demand greater lubrication. The running deck requires periodic lubrication. With average usage (30 minute workout session 3 times a week), lubricate every four to six months. You may adjust the timing of the lubrication based on the intensity of the treadmill use level. To check the lubrication level, simply lift the running belt, and put your hand as far into the center of the belt as you can reach. If your hand shows signs of lubricant (some wetness), then it does not need additional lubrication. If the board feels dry and there is very little evidence of lubricant on your hand, then additional lubrication should be added as instructed:
1.Stop running belt so belt seam is located on the top and in the center of the deck.
2.Insert nozzle into spray head of lubricant can.
3.Lift running belt.
4.Position nozzle between the belt and the board approximately 200 mm (8”) from the front of the treadmill.
5.Apply
6.The treadmill is instantly ready for use.
G B
7
