User modes, User mode screen flow, Press | Ultra electronic Prima 3

(to the next page)

User modes

The settings for printing media, card, etc. can be made in the User mode.

MENU

Press the MENU button when the unit is in the Ready, Preheat or Error status to suspend printing operations.

CAUTION

When you change settings for the

underlined submenu on the next page, (Setting the retransfer film, Setting the retransfer roller temperature and Bend remedy roller temperature setting),the message “Please Reset” will appear on the LCD panel.

Then initialize the printer by pressing

RESET

key and next

ENTER

key.

User mode screen flow

> D o w n l o a d >

MENU

See P.39

MENU

MENU

Press

> T r a n s p o r t M o d e

See P.39

	U s e r M o d e
	and		appears on the LCD panel.
		After 0.5 seconds, the display will switch to
		the following items.
MENU	> D i s p l a y >	MENU	> C o u n t e r R e s e t
		See P.30	See P.31
		See P.30
			MENU
			MENU
	See p. 29		See p. 30
			See p. 30

> H R C o n t r o l

See P.39

MENU See p. 35

> N e t w o r k >

See P.37

MENU

See p.35

> U n i t N o .

See P.36

MENUMENU

Seep. 35

> T e s t P r i n t

See P.36

MENU

See p. 35

> I C C o n t a c t P o s .

See P.36

EXIT

EXIT

EXIT

EXIT

EXIT

EXIT

EXIT

EXIT

EXIT

EXIT

End of user mode

EXIT

EXIT

EXIT

EXIT

EXIT

EXIT

EXIT

EXIT

> C l e a n i n g >

See P.31

MENU

See p. 30

> I n k >

See P.32

MENU

See p. 31

> R e t r a n s f e r >

See P.33

MENU

See p. 32

> B u z z e r

See P.34

MENU

See p. 33

> P o w e r S a v i n g

See P.34

MENUMENU

See p. 35

> I C A n t e n n a P o s .

MENU

See P.36

> M G I S O T y p e

See P.36

See p. 34

			MENU
MENUMENU		MENU	See p. 33
MENUMENU	> C a r d T h i c k n e s s	MENU	> B e n d R e m e d y >
	See P.36		See P.35

See p. 34

27

Image 27

Ultra electronic Prima 3 user manual User modes, User mode screen flow, Press

Contents

Prima Harmonized Standards 89/336/EEC2006/95/EC Relating to electromagnetic compatibility Operation is subject to the following two conditions Information for USA Contents Do not wet the machine with water Do not touch the power plug during electrical stormsManual any time as you need Do not use a line voltage other than instructed Do not touch the power plug with a wet hand Do not use the machine while it has a faultPull out the power plug before cleaning the machine Hold the body of the power plug when pulling it out Handling of transfer film Ink ribbons and cards Product featuresChecking accessories Before use Escape Clause Installation 35% to 70%To 86 F Front Slide knob AccessoryPower input jack Names of parts Please ask your dealer for the Compact IC unit connection Connecting the IC unit Sold separatelyConnecting the Laminator Set-up Check the plug For AC 120V type Connecting the power cordInstall the unit connecting cable.optional Pin Connecting cable Portion B See the description in Jam Transfer on p.50 Installing the card stackerHang the stacker claw on the stacker receptacle Card stacker is capable of containing approximately Setting the ink ribbon Insert the cassette along the guide rail When the ink ribbon is wound up to the endWind the ribbon, taking up the slack Close the printer door Remove the retransfer film cassette Setting the retransfer filmInsert the retransfer film into the cassette Otherwise the printer may fail Slowly If the retransfer film is not set properly When the retransfer film is wound up to the endWind the retransfer film to take up the slack Open the printer door and insert the cassette Shown in the illustration Setting cardsThis 300 pieces is not a guaranteed quantity Cassette and/or the ink ribbon cassette Dealer For a magnetic or IC card, encoding error may happen When moving the card bracketConsult your dealer to purchase new gloves See p.34 in this manual Printing on cards with magnetic strips is not guaranteedFor JIS II cards For ISO cards Connect the printer and host computer with the USB cable Connecting with a host computerConnecting with USB cable Connecting with Ethernet cable Connecting Multiple Printers When connecting a host computer to multiple printersCopyright of the Software is displayed Names of parts on the operation panel Beforeuse LCD operation display content Operation display LED contents LCD panel Operation display LED Ready LED will light up Turning on the powerTurn the power on Represents on and O represents OFF Operation Turning off the power About the Reset buttonIs loaded User mode screen flow User modesPress Submenu Main menu Submenu To the next Display mode settings Exit user Reset the free counterPress to reset Clearing the free counter Special ink SP-Ink 2 level Ink mode settingUV ink level setting Set the K printing mode2 Retransfer mode setting Exit user mode Set the buzzer Buzzer mode setting To select the setting value and press Setting the bend remedy modeSet the bend remedy roller temperature Bend remedy speed settings Unit No. Setting Card Thickness setting mode IC contact setting modeCoercivity setting mode Non-contact IC antenna setting mode Network setting Input method Address Setting mode Low temperature stand-by mode setting Download mode settingSet position of MAC address print Close the card tray CareandcleaningCleaning the cleaning rollers Open the card tray Remove the cleaning unit Wipe the head indicated with Cleaning the thermal headCleaning the fan filter See p.14, 16 in this manual See p.31 in this manual Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions If the sponge is removed, attach it again as shown below Cleaning the magnetic head Set a cleaning cardConfirm that the retransfer film cassette has been removed Cleaning of the bobbin holders Once printer servicing and cleaning Have been completedPeriodical Maintenance Layout of rollers inside the printer TroubleshootingCleaning unit All rollers require routine cleaning To initialize the unit Error code listing MG mechanical error Hardware errorError MG connection error Mending broken ink ribbon Retransfer film Stopping when printingAbout printing errors When retransfer operation is not complete Hopper jam Pull out the card tray Removing card jams Injury Retransfer section Jam transfer Main specifications Specifications 34.3 38.1 External appearance and dimensionsCase of disposal Front view Ultra Electronics Card Systems