Connecting with a host computer | Ultra electronic Prima 3 instruction

(to the next page)

Connecting with a host computer

CAUTION Do not switch off the power of the

host computer during printing.

Do not use the sleep or the stand-by function on the host computer.

If the power of the host computer is switched off during printing, or if the sleep or the stand-by function of the host computer is activated, the printer may stop with cards printed halfway remain

in the printer. When this occurs, initialize the printer as “Stopping when printing”of page 48 on this manual.

Connecting with USB cable

1.Check to ensure that the power of both the printer and host computer are switched off.

2. Connect the printer and host computer with the USB cable.

Insert the USB cable to the USB cable connection terminal at the back of the printer.

USB cable (Accessories)

CAUTION

The location of terminals varies with the host computer. Please refer to the instruction manual of the host computer.

When there are multiple USB cable connection terminal on the host computer, either one can be used.

Do not connect to the USB connection terminal on the host computer’s monitor or keyboard. It may not be recognized correctly.

When using a USB hub, connect to the hub that is directly linked to the host computer.

Connecting with Ethernet cable

1.Check to ensure that the power of both the printer and host computer are switched off.

2. Connect the printer and network HUB is connecting the host computer with the Ethernet cable.

Insert the Ethernet cable to the Ethernet cable connection terminal at the back of the printer.

CAUTION

Adjust orientation of the USB cable according to the terminal, and insert it all the way in.

CAUTION

Consult your dealer on the cable connection if there are USB or serial cable connection

CAUTION

connected during power on.

HUB

USB has priority if an USB cable is

terminal on the printer’s optional port.

CAUTION

Insert the LAN cable all the way in until it stops according to the orientation of the terminal.

CAUTION

To avoid any malfunctions, use a sealed type LAN cable.

21

Image 21

Ultra electronic Prima 3 Connecting with a host computer, Connecting with USB cable, Connecting with Ethernet cable

Contents

Prima 2006/95/EC 89/336/EECRelating to electromagnetic compatibility Harmonized Standards Operation is subject to the following two conditions Information for USA Contents Manual any time as you need Do not touch the power plug during electrical stormsDo not use a line voltage other than instructed Do not wet the machine with water Pull out the power plug before cleaning the machine Do not use the machine while it has a faultHold the body of the power plug when pulling it out Do not touch the power plug with a wet hand Checking accessories Product featuresBefore use Handling of transfer film Ink ribbons and cards Escape Clause Installation 35% to 70%To 86 F Power input jack AccessoryNames of parts Front Slide knob Connecting the Laminator Connecting the IC unit Sold separatelySet-up Please ask your dealer for the Compact IC unit connection Install the unit connecting cable.optional Connecting the power cordPin Connecting cable Check the plug For AC 120V type Hang the stacker claw on the stacker receptacle Installing the card stackerCard stacker is capable of containing approximately Portion B See the description in Jam Transfer on p.50 Setting the ink ribbon Wind the ribbon, taking up the slack When the ink ribbon is wound up to the endClose the printer door Insert the cassette along the guide rail Insert the retransfer film into the cassette Setting the retransfer filmOtherwise the printer may fail Slowly Remove the retransfer film cassette Wind the retransfer film to take up the slack When the retransfer film is wound up to the endOpen the printer door and insert the cassette If the retransfer film is not set properly This 300 pieces is not a guaranteed quantity Setting cardsCassette and/or the ink ribbon cassette Shown in the illustration Dealer For a magnetic or IC card, encoding error may happen When moving the card bracketConsult your dealer to purchase new gloves For JIS II cards Printing on cards with magnetic strips is not guaranteedFor ISO cards See p.34 in this manual Connecting with USB cable Connecting with a host computerConnecting with Ethernet cable Connect the printer and host computer with the USB cable Connecting Multiple Printers When connecting a host computer to multiple printersCopyright of the Software is displayed Names of parts on the operation panel Beforeuse LCD operation display content Operation display LED contents LCD panel Turn the power on Represents on and O represents OFF Turning on the powerOperation Operation display LED Ready LED will light up Turning off the power About the Reset buttonIs loaded User mode screen flow User modesPress Submenu Main menu Submenu To the next Display mode settings Press to reset Reset the free counterClearing the free counter Exit user UV ink level setting Ink mode settingSet the K printing mode2 Special ink SP-Ink 2 level Retransfer mode setting Exit user mode Set the buzzer Buzzer mode setting Set the bend remedy roller temperature Setting the bend remedy modeBend remedy speed settings To select the setting value and press Coercivity setting mode Card Thickness setting mode IC contact setting modeNon-contact IC antenna setting mode Unit No. Setting Network setting Input method Address Setting mode Low temperature stand-by mode setting Download mode settingSet position of MAC address print Cleaning the cleaning rollers CareandcleaningOpen the card tray Remove the cleaning unit Close the card tray Cleaning the fan filter Cleaning the thermal headSee p.14, 16 in this manual Wipe the head indicated with Install the fan filters back to the original positions Cleaning the card feed rollers and heat RollersIf the sponge is removed, attach it again as shown below See p.31 in this manual Cleaning the magnetic head Set a cleaning cardConfirm that the retransfer film cassette has been removed Cleaning of the bobbin holders Once printer servicing and cleaning Have been completedPeriodical Maintenance Cleaning unit TroubleshootingAll rollers require routine cleaning Layout of rollers inside the printer To initialize the unit Error code listing Error Hardware errorMG connection error MG mechanical error About printing errors Stopping when printingWhen retransfer operation is not complete Mending broken ink ribbon Retransfer film Hopper jam Pull out the card tray Removing card jams Injury Retransfer section Jam transfer Main specifications Specifications Case of disposal External appearance and dimensionsFront view 34.3 38.1 Ultra Electronics Card Systems