Set position of MAC address print
In the case of UV print, MAC address must be printed at the edge of a card at the same time. Position of MAC address is selectable between Right Upper Edge or Left Bottom Edge via Command or opration panel. Please refer to following picture 1 about print position. Following mentioned coordinates are based
on “Starting point of Print Area” and indicated in pixels.
| Starting Point of |
| Print Area(0,0) |
B |
|
(42,611) |
|
Print position of MAC | |
address in case | |
that it is set at | 5678- |
| |
Lower Left position. | 1234 |
| |
| (764,18) |
| A |
Direction of Retransfer |
|
|
|
|
|
| ||
| 1234- | 230 | ||||||
|
|
|
| |||||
| position of MAC address | 5678- | ||||||
| Pixel | |||||||
|
|
|
| |||||
| in case that it is set at |
|
| 90AB | ||||
| Upper Right position. |
|
|
|
| |||
|
|
|
|
| ||||
|
|
|
|
|
| |||
34
Pixel
(1035,663)
Fig. 1 Print Position of MAC address
CAUTION
In case that UV is printed on YMC directly, print error will be occurred when retransferring. So in case that YMC image is overlapped with UV image, please print UV image on the retransfer film after YMC image is retransferred on the card. It is requested to pay the same special attention for MAC address that is printed with UV ink.
So in case that MAC address print area with UV ink is overlapped with with
Low temperature stand-by mode setting
Please set ON normally in this mode. When the printer is set ON in this mode, the printer will become standby at low temperature of the retransfer heat roller after no printing motion for 30 minutes and over. The temperature of the heat roller will automatically get an original setting when next card printing command received. For that reason, it takes long time for 1st card compared with normal printing.
Availability of heat roller control at the
> H R C o n t r o l |
| EXIT | Exit user |
|
|
|
|
| |
| o f f |
| mode. |
|
Press |
|
| ENTER | to save. |
to select the setting press | ||||
(The electronic beep sounds .The beep will not sound if the buzzer mode setting is set to off.)
DOWNLOAD mode setting
Set the printer to DOWNLOAD mode.
CAUTION When data is transferring from thee host computer, “Downloading” will be displayed
If the power is turned off at this time, the printer firmware will crash and the printer cannot operate.
| > D o w n l o a d |
| EXIT |
| Exit user mode | ||||||
|
|
|
|
|
| O K ? |
|
|
| ||
|
|
|
|
|
|
|
|
| EXIT |
| |
|
|
|
|
|
|
|
|
|
|
| |
ENTER |
|
| Press ENTER key to set DOWNLOAD mode. | ||||||||
|
|
|
|
| |||||||
|
|
|
| (The electronic beep sounds, The beep will not |
|
|
| ||||
|
|
|
| sound if the buzzer mode setting to off) |
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| > D o w n l o a d R e a d y |
| EXIT |
| > D o w n l o a d i n g > | ||||||
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
| P o w e r O f f | |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Start |
|
|
|
| |
| Completion |
|
|
| When data is received from the Host | ||||||
|
| ||||||||||
|
|
|
|
|
|
|
| ||||
| > D o w n l o a d i n g |
| |||||||||
|
| computer,Downloading will be displayed. | |||||||||
|
|
|
| K e e p p o w e r O n |
| ||||||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| Transport mode | ||
| ||||
To set the transport mode. | ||||
|
| EXIT | ||
> T r a n s p o r t m o d e |
| |||
|
| O K ? |
| Exit user mode |
|
|
| ||
|
|
|
| |
|
|
|
|
|
ENTER |
| to carry out transport mode. | ||
| ||||
Press |
| |||
|
| (The electronic beep sounds.The beep will not | ||
|
| |||
|
| sound if the buzzer mode setting is set to off.) | ||
P l e a s e , |
| Please turn off the power. | ||
P o w e r o f f |
| Turning on the power, then the | ||
| transport mode is canceled. | |||
CAUTION
When shipping or moving the printer, you must set the transport mode. If the printer is not set
the transport mode, it may have a damage.
39
