Connecting the power cord | Ultra electronic Prima 3 specification

Set-up(continued)

CAUTION

Be careful not to pinch your finger when installing.

2. install the laminator

Laminator(ILU)

Memo

If the mounting is uneven, the card would not be transported smoothly. be sure to fit the units right in. Always install the unit at a horizontal and hard surface location

3. Install the unit connecting cable.(optional)

As shown in the diagram, connect the cable to the OPTION 2 external connection terminal of the printer and the PRINTER external connection terminal of the laminator.

OPTION2

PRINTER

9 pin

9 pin

Connecting cable

Connecting the power cord

1.Check the plug.

• For AC 120V type	• For AC220-240V type
(North America)	(Europe)

*The detached power cords vary according to model and country of purchase.

2. Plug the power cable into the printer.

Plug the power cable of the laminator if it is installed.

CAUTION

Always use a grounded power outlet. Never share the outlet with other electrical equipment.

Tight the screw after connecting

CAUTION

Make sure to tighten the screws of the interface cables.

Use an AVR (Automatic Voltage Regulator) if there is a possibility of voltage fluctuation. Use an uninterruptible power source rather than an AVR if there is the possibility of uninterruptible power source.

12

Image 12

Ultra electronic Prima 3 Connecting the power cord, Install the unit connecting cable.optional, North America Europe

Contents

Prima 89/336/EEC 2006/95/ECRelating to electromagnetic compatibility Harmonized Standards Information for USA Operation is subject to the following two conditions Contents Do not touch the power plug during electrical storms Manual any time as you needDo not use a line voltage other than instructed Do not wet the machine with water Do not use the machine while it has a fault Pull out the power plug before cleaning the machineHold the body of the power plug when pulling it out Do not touch the power plug with a wet hand Product features Checking accessoriesBefore use Handling of transfer film Ink ribbons and cards Escape Clause Installation 35% to 70%To 86 F Accessory Power input jackNames of parts Front Slide knob Connecting the IC unit Sold separately Connecting the LaminatorSet-up Please ask your dealer for the Compact IC unit connection Connecting the power cord Install the unit connecting cable.optionalPin Connecting cable Check the plug For AC 120V type Installing the card stacker Hang the stacker claw on the stacker receptacleCard stacker is capable of containing approximately Portion B See the description in Jam Transfer on p.50 Setting the ink ribbon When the ink ribbon is wound up to the end Wind the ribbon, taking up the slackClose the printer door Insert the cassette along the guide rail Setting the retransfer film Insert the retransfer film into the cassetteOtherwise the printer may fail Slowly Remove the retransfer film cassette When the retransfer film is wound up to the end Wind the retransfer film to take up the slackOpen the printer door and insert the cassette If the retransfer film is not set properly Setting cards This 300 pieces is not a guaranteed quantityCassette and/or the ink ribbon cassette Shown in the illustration Dealer For a magnetic or IC card, encoding error may happen When moving the card bracketConsult your dealer to purchase new gloves Printing on cards with magnetic strips is not guaranteed For JIS II cardsFor ISO cards See p.34 in this manual Connecting with a host computer Connecting with USB cableConnecting with Ethernet cable Connect the printer and host computer with the USB cable Connecting Multiple Printers When connecting a host computer to multiple printersCopyright of the Software is displayed Beforeuse Names of parts on the operation panel Operation display LED contents LCD panel LCD operation display content Turning on the power Turn the power on Represents on and O represents OFFOperation Operation display LED Ready LED will light up Turning off the power About the Reset buttonIs loaded User mode screen flow User modesPress Submenu To the next Main menu Submenu Display mode settings Reset the free counter Press to resetClearing the free counter Exit user Ink mode setting UV ink level settingSet the K printing mode2 Special ink SP-Ink 2 level Retransfer mode setting Buzzer mode setting Exit user mode Set the buzzer Setting the bend remedy mode Set the bend remedy roller temperatureBend remedy speed settings To select the setting value and press Card Thickness setting mode IC contact setting mode Coercivity setting modeNon-contact IC antenna setting mode Unit No. Setting Network setting Input method Address Setting mode Low temperature stand-by mode setting Download mode settingSet position of MAC address print Careandcleaning Cleaning the cleaning rollersOpen the card tray Remove the cleaning unit Close the card tray Cleaning the thermal head Cleaning the fan filterSee p.14, 16 in this manual Wipe the head indicated with Cleaning the card feed rollers and heat Rollers Install the fan filters back to the original positionsIf the sponge is removed, attach it again as shown below See p.31 in this manual Cleaning the magnetic head Set a cleaning cardConfirm that the retransfer film cassette has been removed Cleaning of the bobbin holders Once printer servicing and cleaning Have been completedPeriodical Maintenance Troubleshooting Cleaning unitAll rollers require routine cleaning Layout of rollers inside the printer Error code listing To initialize the unit Hardware error ErrorMG connection error MG mechanical error Stopping when printing About printing errorsWhen retransfer operation is not complete Mending broken ink ribbon Retransfer film Removing card jams Hopper jam Pull out the card tray Injury Retransfer section Jam transfer Specifications Main specifications External appearance and dimensions Case of disposalFront view 34.3 38.1 Ultra Electronics Card Systems