Univex PRV-LX1 manual 96

TROUBLESHOOTING

Symptom	Cause/Remedy	Reference page
Cannot playback on DVD player /	¶ When discs recorded in video mode are to be played back on	44
other DVD recorders.	other players, be sure to finalize them after recording (however,
	some discs may be unplayable on other players even after
	finalization).
Image stops during playback, or	¶ Press the EJECT button once and then start playback again.
commands are disabled.
Main unit command buttons	¶ Hold the STANDBY/ON button depressed for 4 seconds or more
don’t work.	to set unit to standby condition. If the STANDBY/ON button also
	doesn’t work, turn off the main power switch on the rear panel.
Can’t output 96 kHz audio in	¶ Some discs prohibit digital output of 96 kHz linear PCM audio. In	50
digital.	this case, even if the unit’s [96 kHz PCM OUT] command is set
	to “96 kHz”, the signal will be converted to 48 kHz for output.
Remote control unit doesn’t	¶ Operate remote within proper range (7 m).	17
work.	¶ Change to new batteries.	17
Television malfunctions.	¶ Video monitors with wireless remote control functions may
	malfunction when the PRV-LX1’s remote control unit is used. In
	such cases, separate the television monitor and the PRV-LX1.
Memory settings are erased.	¶ If manual disconnection of the power cord or a power failure	6
	occurs when the unit is turned on, previously input settings may
	be erased. Before disconnecting the power plug, always press
	the unit’s STANDBY/ON (POWER) button and wait until the
	display’s [POWER-OFF] display disappears, then set the rear
	panel’s power switch to OFF.
No sound from speakers, or	¶ If video monitor or AV amplifier’s sound volume is set to
distorted sound.	minimum, raise the sound volume.
	¶ When using audio input from external input connector, set the	37
	[Audio Level] command.
	¶ Check and confirm that all audio cables are connected properly.
	¶ Check that all cable plugs are inserted securely in their
	connectors or jacks.
	¶ Clean any dirt from connection plugs and jacks.
	¶ No sound is produced during still, frame advance, and slow playback.
	¶ DTS audio is output only from unit’s digital audio output	50
	connectors. To listen to DTS audio from a DVD disc, the unit’s
	digital audio output connectors must be connected to the digital
	audio input connectors of a DTS compliant amplifier, and the
	[DTS OUT] command must be set to “ON”. If the connected
	amplifier does not support DTS audio, use the remote control
	unit’s AUDIO button or the disc menu to select an audio format
	other than DTS.
When a professional VTR is	¶ Connect this unit directly to the professional VTR.
connected to this unit’s DV	¶ Check that the DV cable is connected properly.
connectors, the appear cannot
	¶ Turn on the power again to the professional VTR.
be viewed on a video monitor,
	¶ Turn the power to the PRV-LX1 OFF then ON again.
or no sound is produced.
DVD playback images cannot be	¶ Connect this unit directly to the professional VTR.
viewed on the screen of the	¶ Check that the DV cable is connected properly.
professional VTR connected to
	¶ Try stopping playback and then starting it again.
the DV connectors, or no sound
	¶ Turn on the power again to the professional VTR.
is produced.
	¶ Turn the power to the PRV-LX1 OFF then ON again.
	¶ The video and audio of DVDs labeled “copying prohibited” or
	“copy once only” cannot be output.
	¶ The audio/video of a component connected to an external input
	connector cannot be output.
	¶ No video or audio signals are output during recording or during
	recording pause.	52
	¶ Set [DV OUT] to “Enabled”.

96

PRV-LX1 En