OWNER’S MANUAL

OPERATING

FIREPLACE

FOR YOUR SAFETY

READ BEFORE

LIGHTING

WARNING: If you do not fol- low these instructions exactly, a fire or explosion may result caus- ing property damage, personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas sup- plier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been un- der water.

LIGHTING

INSTRUCTIONS

1.STOP! Read the safety information above on this label before proceeding.

2.Set the “HI-LO” knob to the lowest setting.

3.Turn off all electrical power to the appliance.

4.Open control access panel.

5.Push in gas control knob slightly and

turn clockwise to “OFF”.

6.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety in- formation on this page. If you don’t smell gas, go to the next step.

7.The pilot is located by the main burner.

8.Turn knob on gas control counter-

clockwise to “PILOT”.

9.Push in the control knob all the way and hold in. Immediately light the pi- lot by pressing the ignitor button until a flame appears one (1) minute after the pilot is lit. Release knob and it will pop back up. Pilot should re- main lit. If it goes out, repeat steps 5 through 9.

•If knob does not pop out when re- leased, stop and call gas supplier.

•If the pilot will not stay lit after sev- eral tries, turn gas control knob to “OFF” and call your service tech- nician or gas supplier.

10.Turn gas control knob counterclock-

wise to “ON”. Knob can be turned to “ON” only if the control knob is popped out.

11.Set “HI-LO” knob to desired setting.

12.Turn on all electric power to the ap- pliance.

Gas Control Knob

 

HI/LO Knob

 

 

 

 

IL

O

 

 

 

 

T

 

 

 

 

P

 

 

 

N

 

16AI

 

 

 

O

 

 

 

O

T

 

 

 

TH

 

 

 

7

I

 

 

L

 

 

 

 

P

L

I

 

 

 

FFO

O

H

 

TP

 

E

A

 

 

TPTH

 

 

 

 

Position Indicator

Figure 50 - Control Knob in the PILOT Position

TO TURN OFF GAS

TO APPLIANCE

1.Turn off the wall switch.

2.Turn off all electric power to the ap- pliance if service is to be performed.

3.Remove control access panel.

4.Push in gas control knob slightly and

turn clockwise to “OFF”. Do not force.

5.Replace control access panel.

Continued

106918

21

Page 20 Page 22
Page 21
Image 21
Vanguard Heating VDDVF36STN/STP Operating Fireplace, For Your Safety Read Before Lighting, Lighting Instructions
Page 20 Page 22

VDDVF36STN/STP, VDDVF36PN/PP specifications

The Vanguard Heating VDDVF36PN/PP and VDDVF36STN/STP are premium direct vent gas fireplaces that seamlessly blend contemporary design with advanced heating technologies. These models are perfect for homeowners looking to enhance their living spaces while ensuring optimal warmth and comfort.

One of the key features of the VDDVF36 series is its powerful heating capacity. With a maximum input of 36,000 BTUs, these fireplaces can efficiently warm large rooms, making them an excellent choice for both new constructions and renovations. Their direct vent system allows for flexible installation options, as it can draw air from outside and exhaust gases without needing an existing chimney.

The design aesthetic of the VDDVF36PN/PP and VDDVF36STN/STP models is notably sleek and modern. Available in either a pristine perfect black finish or a striking stainless steel option, these units can complement a variety of interior styles. The large viewing area, framed by a stylish bezel, ensures that the flames are the focal point of the room, establishing a cozy ambiance.

Equipped with advanced electronic ignition, these fireplaces offer ease of use and reliability. The ignitor provides a fast and safe startup, eliminating the need for manual lighting and enhancing the user experience. Additionally, these units come with a built-in thermostatic control, allowing users to regulate temperatures effectively, ensuring consistent comfort while optimizing energy use.

The VDDVF36 series is also designed with safety in mind. An integrated safety shut-off system ensures that the fireplace will automatically turn off if any issues are detected, providing peace of mind for users. Furthermore, the screens and barriers are designed to prevent accidental contact with the flames, making them safe for households with children and pets.

In terms of maintenance, the VDDVF36 models are designed for easy access to components, making regular cleaning and servicing straightforward. The durable construction materials used in these fireplaces ensure longevity and reliability, promising years of efficient heating.

Overall, the Vanguard Heating VDDVF36PN/PP and VDDVF36STN/STP models represent the pinnacle of modern gas fireplace technology, combining powerful heating capabilities, stylish aesthetics, and advanced safety features into one outstanding unit. For homeowners seeking a reliable and attractive heating solution, these fireplaces are an excellent choice.
Top Page Image Contents