Vermont Castings Jefferson Direct Vent/Natural Vent Gas Heater

3.Attach the fan to the rear shroud by engaging the upper flange of the fan skirt under the lower edge of the shroud and secure the skirt with the four screws and one star washer provided. (Fig. 14)

4.The rheostat control switch attaches to the left side of the valve bracket at the front of the stove.

•Remove the plug from the rheostat bracket.

•Insert the switch box shaft through the hole in the back of the right side of the valve bracket, aligning the locator pin with the smaller hole in that bracket.

•Attach the retaining nut to the switch control shaft to secure it to the plate.

•Attach the Control Knob to the rheostat shaft.

•Use the wire tie to secure the fan and rheostat wire harnesses together.

Upper

Flange

to

Control

Valve

ST240

Fig. 19 The upper flange of the fan skirt should be located behind the lower edge of the shroud.

ST241

Fig. 20 Correct position of fan skirt installation.

Venting System Assembly - Direct Vent

General Information

The Jefferson is approved for installation only with the vent components listed on Page 12. Follow the vent component instructions exactly.

For U.S. installations: The venting system must conform with local codes and/or the current National Fuel Gas Code, ANSI Z223.1

For Canadian installations: The venting system must conform to the current CSA B149.1 installation code.

Install the Vent Adapter Pipe

(CFM Vent Components)

1.Install the Restrictor Plate. Consult the ÔVent Run SpecificationsÕ on page 8 to determine whether the restrictor plate is needed. If so, put the restrictor plate in place within the inner flue collar as shown in Figure 16. NOTE: The restrictor plate supplied with the vertical termination should be discarded. Install restrictor plate supplied with the stove directly at stove outlet.

ST210

Fig. 16 Install the restrictor plate only if required for the venting configuration. Refer to page 8.

2.Attach Inner Starter Pipe, (found in with the logset), to the next section of inner pipe.

•Run a bead of sealant about 1/2Ó from the upper end of the Inner starter pipe and join the two sec- tions together.

•Drill three pilot holes into the Inner Starter and secure the assembly with three sheet metal screws. (Fig. 17)

3.Dry fit the Inner pipe assembly to the stove and determine the required vent length.

•Insert the vent assembly into the flue collar, but do not attach. Measure to determine the correct length required for your installation and cut the upper end of the pipe as necessary.

•Dry fit the outer vent section and cut to match the height of the Inner assembly.

14

20002191

Page 13 Page 15
Page 14
Image 14
Vermont Casting 2823, 820, 2828, 2825 Venting System Assembly Direct Vent General Information, Install the Vent Adapter Pipe
Page 13 Page 15

2823, 2825, 820, 2827, 2828 specifications

Vermont Casting stoves are renowned for their quality and performance, with models such as the 2823, 2822, 2828, 820, and 2825 exemplifying the brand’s dedication to craftsmanship and innovation. Each model presents unique features and technologies that cater to different heating needs and preferences.

The 2823 model is a testament to Vermont Casting's commitment to efficiency and style. It boasts a clean-burning gas system that maximizes heat output while minimizing emissions. Additionally, the model's design emphasizes both aesthetic appeal and functionality, making it a perfect centerpiece for any room. With its user-friendly controls, it allows easy adjustments to heat levels, offering a tailored experience for homeowners.

The 2822 model is known for its compact design, making it an ideal choice for smaller spaces. Despite its size, it does not compromise on performance, delivering a substantial heat output. This model is equipped with a dual-burner system that enhances its heating capabilities, ensuring a consistent and comfortable environment. Furthermore, its built-in safety features provide peace of mind, allowing users to enjoy their heating solution with confidence.

In contrast, the 2828 model offers a higher output, perfect for larger areas. Its innovative heat exchanger technology ensures optimal heat distribution throughout the space, making it a favorite among those with bigger homes. The model’s sleek design and customizable options allow homeowners to choose finishes that complement their existing decor, enhancing both the visual and functional aspects of their living areas.

The 820 model stands out with its unique style, offering a combination of traditional and modern aesthetics. This model features a powerful combustion system that maximizes efficiency while reducing fuel consumption. Its large viewing window provides a beautiful fire display, turning any space into a cozy retreat. The 820 is particularly favored among users who appreciate the ambiance of a traditional fireplace with the convenience of modern technology.

Finally, the 2825 model is designed for users seeking maximum customization. Its adjustable heating options and multiple finish choices allow homeowners to create a truly personalized experience. The advanced technology incorporated into the 2825 ensures enhanced performance, making it one of the most sought-after models in the Vermont Casting lineup.

In summary, the Vermont Casting 2823, 2822, 2828, 820, and 2825 models each have their unique features that cater to different heating needs. With advanced combustion technologies, customizable designs, and a commitment to efficiency, these stoves highlight Vermont Casting's reputation for quality and innovation in home heating solutions.
Top Page Image Contents