Vermont Castings Jefferson Direct Vent/Natural Vent Gas Heater
Venting Requirements and Options -
Direct Vent ONLY
Approved Vent System Components
The Stardance Heater must be vented to the outdoors through an adjacent exterior wall or through the roof. The venting system must be comprised of the appropri- ate listed venting components specified on this page. These parts are available from DuraVent Corporation or your Vermont Castings Majestic Products Dealer.
See Figure 4 for dimensions relevant to the standard
Simpson DuraVent Components
Minimum Horizontal Vent Kit | 2792 |
(1)Finishing plate (CG)
(1)Finishing collar (CG)
(4)Polished Brass flue pipe rings
Through the Wall Vent Kit | 7TFSDVSK |
(1)
(1)24" Straight pipe (CG)
(1)48" Straight pipe (CG)
(1)Side Wall Termination
(1)Firestop
(1)
(1)Hardware package
(1)Finishing plate (CG)
(1)Finishing collar (CG)
(4)Polished Brass flue pipe rings
Through the Wall Vent Kit for
7TFSDVSKS |
Starter Pipe Assembly (incl. inner & outer sections) | Includes all of the above parts plus |
| ||||
2768* |
|
| (1) | Snorkel Termination | 7TDVSKVA | |
90° Elbow, Blk. |
| 990B* | Vertical Termination Kit, | |||
| (1) | Combination Horizontal Offset / Roof Support | ||||
45° Elbow, Gal. |
| 945 | ||||
| (1) | Vertical Termination |
| |||
6Ó Straight, Blk. |
| 908B* |
| |||
| (1) | Storm Collar |
| |||
9Ó Straight, Blk. |
| 907B |
| |||
| (1) |
| ||||
11Ó - 14⁵⁄₈Ó Adjustable Straight Section |
| 911B |
| |||
| (1) | Finishing Plate (CG) |
| |||
12Ó Straight |
| 906 |
| |||
| (1) | Finishing Collar (CG) |
| |||
24Ó Straight |
| 904B* | (1) | Polished Brass Flue Pipe Ring |
| |
36Ó Straight |
| 903B | (1) | Hardware Package |
| |
48Ó Straight |
| 902 | Vertical Termination Kit, | 7TDVSKVB | ||
Horizontal Vent Cap |
| 984* | (1) | 7/12 - 12/12 Flashing |
| |
Wall Plate* |
| 940 | and all of the other Vertical Termination parts. |
| ||
Vinyl Siding Shield |
| 950 | Vertical Termination, Flat Roof | 7DVSKVF | ||
| (1) | Flat Flashing |
| |||
Snorkel Termination - 14Ó |
| 982 |
| |||
| and all of the other Vertical Termination parts. |
| ||||
Snorkel Termination - 36Ó |
| 981 |
| |||
| Twist Lock 24" Straight Pipe (CG) | 7TFSDVP24 | ||||
Wall Strap |
| 988 | ||||
| (1) | 24" |
| |||
Cathedral Ceiling Support Box |
| 941 |
| |||
| (1) | Polished Brass Flue Pipe Ring |
| |||
Storm Collar |
| 953 |
| |||
| Twist Lock 48" Straight Pipe (CG) | 7TFSDVP48 | ||||
Firestop Spacer |
| 963 | ||||
| (1) | 48" Nonadjustable Pipe |
| |||
Flashing 0/12 - 6/12 |
| 943 |
| |||
| (1) | Polished Brass Flue Pipe Ring |
| |||
Flashing 6/12 - 12/12 |
| 943S | Twist Lock | 7TFSDVT45 | ||
Vertical Termination Cap |
| 991 | for vertical offsets |
| ||
*Included in Minimum Horizontal Vent Kit #2792 |
|
| (1) |
| ||
All DuraVent Straight vent pipe sections have a net | (1) Polished Brass Flue Pipe Ring |
| ||||
length 1¹⁄₂Ó (37mm) less than the nominal dimension; | Draft Hood Adapter | FSDHAG | ||||
i.e., a 6Ó (152mm) Straight pipe section has an |
| NV Stove Kit | 7FSSK | |||
effective length of 4¹⁄₂Ó (115mm). |
|
| (1) | 7Ó Diameter Polished Brass Trim Ring |
| |
CFM Vent Components |
|
| (1) | 48Ó Nonadjustable Pipe (CG) |
| |
|
| (1) | 24Ó Nonadjustable Pipe (CG) |
| ||
The following kits are available to meet the needs of | (1) Finishing Plate |
| ||||
most installations. All pipe has a 7" outer diameter and | (1) | Finishing Collar (CG) |
| |||
(1) | 90 Degree Elbow (CG) |
| ||||
includes a 4" diameter inner section. A (CG) designa- |
| |||||
Stove Kit | 7FSDHASK | |||||
tion indicates the part is finished in Charcoal Gray | ||||||
Includes all parts in the 7FSSK plus the Draft Hood Adapter | ||||||
paint. Consult your dealer about other vent parts that | ||||||
FSDHAG |
| |||||
may be appropriate to complete the installation. |
|
| ||||
| Combination Offset/Roof Support | 7DVCS | ||||
Min. Through the Wall Vent Kit | 7TFSMSK | |||||
Attic Insulation Shield | 7DVAIS | |||||
(1) |
|
| ||||
|
| 7" Charcoal Gray Pipe Rings, (4) | 7FSDRG | |||
(1) 24" Straight pipe (CG) |
|
| ||||
|
| 7" Polished Brass Pipe Rings (4) | 7FSDRP | |||
(1) 36" Straight pipe (CG) |
|
| ||||
|
| Wall Thimble | 942G | |||
(1) Side Wall Termination |
|
| ||||
|
| NOTE: Direct vent pipe may be used on the Natural | ||||
(1) Firestop |
|
| ||||
|
| Vent system from the top of the draft hood adapter to | ||||
(1) |
|
| ||||
(1) Hardware package |
|
| the ceiling. |
| ||
12 | 20002191 |
