4Operation, Turning on the Power | Vidikron 90 manual

4Operation

1.Turn on the main power switch on the projector.

2.Press the ON button on the remote control -- or the POWER button on the Vision 90 rear panel -- to turn on the projector. The vacuum fluorescent display on the Vision 90 rear panel briefly displays “Starting Display.”

3.When the projector is ready for use, the fluorescent display indicates the active source, signal format (NTSC or PAL), input resolution and aspect ratio; for example:

		Input
Current Source	Format	Resolution

4.1

Turning on the Power

Component SD NTSC				480i
Anamorphic				Vidikron 90

Aspect

Ratio

By default, the Vision 90 is configured for a “floor/front” installation, in which the projector is installed upright and in front of the screen. If it is installed behind the screen and/or mounted on a ceiling, you must change the picture orientation. To do this:

1.Press MENU and enter the Service Menu passcode.

2.Select Service from the Main Menu.

3.Select Display Device from the Service Menu.

4.Select Installation from the Display Device menu.

5.Choose Floor/Rear, Ceiling/Front or Ceiling/Rear, to match the installation method.

You must enter a passcode to access the Service menu.

Note

4.2

Adjusting the Picture Orientation

Vidikron Vision Model 90 Owner’s Operating Manual

4-1

Image 35

Vidikron 90 manual 4Operation, Turning on the Power, Adjusting the Picture Orientation

Contents

DLP Projector Page For Projectors, Video Processors and Controllers TWO Year Limited Warranty Effective Warranty Date Vidikron Safety Precautions 1Table of Contents Serial Communications Maintenance and TroubleshootingSpecifications Operation 1List of Figures List of Figures About This Manual 1Introduction If you need Turn to Using This Manual Key Features and Benefits Description, Features and Benefits Optional Accessories Vision 90 at a Glance 2Controls and Functions Vision 90 Rear Panel Component Video RCA connectorsHD1 / HD2 Analog BNC connectors Video 1 / S-VIDEO Volt 800 mA Trigger Outputs Vision 90 Remote Control Functions Vision 90 Remote Control Cust Memory Preset Buttons ISF NT NightOn / OFF Cursor Keys DVI 1 6 / DVI 2 VideoComp Component HD 1 4 / HD 2 Remote Control 3Installation Step Procedure For Details Refer to Quick SetupInstallation Overview Advantages Considerations Installation ConsiderationsProjector Installation Options Installation Type Flat vs. Curved Screens Estimating Throw Distance Ambient Light Throw Ratio Throw Distance Range Vision 90 Lens OptionsVertical and Horizontal Position Vertical Lens Shift Shift Lens Option Adjusting the ProjectionVertical and Horizontal Lens Shift Limits Angle Folded Optics DVI Connections See Figure Connections to the Vision Digital DTV RGB Connections Digital DTV RGB Connections See Figure Analog RGB Connections Analog Computer RGB Connections See Figure 10. Composite, S-Video and Component Video Connections Composite/S-Video/Component Video Connections See Figure Components Connecting 12-Volt TriggerConnection 4Operation Turning on the PowerAdjusting the Picture Orientation Focus Zoom Shift Lens AdjustmentsUsing the On-Screen Menus Aspect Ratio ISF PresetsService Input Source Input Source Composite Video Component SD Main MenuInput Source Aspect Ratio Description Aspect Ratio Settings Picture Brightness Contrast Color Tint Sharpness Perform the adjustments in the order listed herePicture Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan Input Position Should be used by ISF-certified technicians only ISF PresetsInformation Calibration Operation Service Code sent by the remote to match as described below Operation Symptom Possible Causes Solution 5Maintenance and TroubleshootingLamp Replacement Troubleshooting Tips Troubleshooting Chart Maintenance and Troubleshooting Command Parameter Value Description Min/max Stored? Serial Command SyntaxSerial Commands RS-232 Connection and Port Configuration Serial Communications CUSTOM1 YES Command Parameter Value Description Min/max Vision 90 Specifications 7Specifications Dimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power Requirements Regulatory Approvals Limited WarrantySpecifications are subject to change without notice Vision 90 Dimensions Vision 90 DimensionsPage RUMA-011150