Index
VXI-MXI User Manual Index-4 © National Instruments Corporation
environmental specifications, A-2 to A-3
equipment, optional, 1-6 to 1-7
ETOEN bit, 4-43
ETRG[7-0]DIR bit, 4-27
ETRG[7-0]EN bit, 4-27
ETRIG bit, 4-44
EXT CLK connector, 6-2
EXT CLK SMB input/output
configuration, 3-20
Extended P2 ECL Trigger Line Support (1)
bit, 4-28
Extended P3 ECL Trigger Line Support (1)
bit, 4-28
Extended TTL Trigger Line Support (0)
bit, 4-28
Extended Utility Line Support (0) bit, 4-28
F
FAIR bit, 4-34
front panel of VXI-MXI interface module,
1-5
functional description. See theory of
operation.
H
hard resets, 4-1
High/Low configuration format, 5-5
I
I[15-0] bits, 4-51
IACK cycle, 6-4 to 6-5
installation, 3-23 to 3-31. See also
configuration.
INTX daughter card
cable connection, 3-27
INTX termination, 3-25 to 3-26
parts locator diagram, C-3, C-4
reinstalling INTX card, C-4
removing from VXI-MXI, C-3
removing metal enclosure, C-1
VXI-MXI parts locator diagram, C-2
MXIbus cable connection, 3-28 to 3-29
MXIbus termination, 3-24 to 3-25
procedure for, 3-26 to 3-27
system power cycling requirements, 3-30
to 3-31
unpacking the VXI-MXI interface
module, 1-7
interlocked arbitration mode, configuration,
3-13 to 3-14
Interrupt and Timing Extension (INTX)
daughter card. See INTX daughter card.
interrupt circuitry
definition, 2-7
interrupt acknowledge (IACK) cycle, 6-4
to 6-5
INTX daughter card, 2-9
Status/ID information, 6-5
theory of operation, 6-3 to 6-6
VXI-MXI addresses for VMEbus
interrupt levels, 6-5
interrupt handler compliance levels, 2-4
Interrupt Status/Control Register, 4-45
to 4-47
interrupter compliance levels, 2-4
INTLCK bit, 4-33
INTX daughter card
block diagram, 2-8
cable connections, 3-27
CLK10 control, 2-9
CLK10 mapping, 3-20 to 3-22
connector description, D-3 to D-4
connectors, 2-7
factory default settings, 3-3
illustration, 1-3
installation
parts locator diagram, C-3, C-4
reinstalling INTX card, C-4
removing from VXI-MXI, C-3
removing metal enclosure, C-1
VXI-MXI parts locator diagram, C-2
interrupt control, 2-9
registers, 2-8
routing CLK10 signal from INTX
connector, 3-18
signal assignments, D-3
signal groupings, D-4
system reset control, 2-9
termination, 3-25 to 3-26
trigger control, 2-9
INTX Interrupt Configuration Register,
2-8, 4-26
INTX Trigger Configuration Register,
2-8, 4-27
INTX Utility Configuration Register,
2-8, 4-28 to 4-29
IRQ Acknowledge Registers, 4-51
IRQ[7-1] bit, 4-47
ITS[3-0] bits, 4-42