Manuals / White Rodgers / Household Appliance / Thermostat

White Rodgers 1F92W-51 manual Subbase

Models: 1F92W-51

1 52

Download 52 pages 63.81 Kb

Page 12

Figure 3. Subbase

!WARNING

DO NOT EXCEED MAXIMUM VOLTAGE OR CURRENT RATINGS. FIRE, PERSONAL IN- JURY, AND/OR EQUIPMENT DAMAGE COULD RESULT.

Expansion

plugs

!CAUTION

To prevent electrical shock and/or equip- ment damage, disconnect electrical power at the main fuse box until installation is complete. Verify power is off with a volt- meter.

Connect wires under

terminal screws

	Mounting		S1 S2 S3
	Mounting	O	W1
	hole	O	W1	4-pin connector
		B	E1		Mounting
		Y1	E2
		Y1	E2
		Y2	L
		Y2	L		hole
		C	R		hole
		G	W2
		9-pin connector W3

Pull wires through

this opening

Figure 3. Subbase

12

Image 12

White Rodgers 1F92W-51 manual Subbase

Contents

INSTALLATION & 1F92W-51OPERATION GUIDE WHITE-RODGERSAbout Your New Thermostat In This Guide THE THERMOSTAT’S SPECIFICATIONSINSTALLING YOUR THERMOSTAT YOUR NEW THERMOSTAT’SYOUR NEW THERMOSTAT’S FEATURES PRECAUTIONS Do not exceed the specification ratingsTHE THERMOSTAT’S SPECIFICATIONS Setpoint Temperature RangeOperating Ambient Temperature Range Shipping Temperature RangeINSTALLING YOUR THERMOSTAT NEW INSTALLATIONROUTE WIRES TO LOCATION SELECT THERMOSTAT LOCATIONFigure 1. Routing thermostat wires REPLACEMENT INSTALLATION TABLE 1. WIRE IDENTIFICATION LABELSREMOVE OLD THERMOSTAT THE WALLTABLE 2. TERMINAL REFERENCE LABELNEW THERMOSTAT OLD THERMOSTATATTACH SUBBASE TO WALL Figure 3. Subbase THERMOSTAT SYSTEMIF SAFETY CIRCUITS ARE IN ONLY ONE OF THE SYSTEM WITH NO SAFETY CIRCUITSSYSTEMS, REMOVE THE TRANSFORMER OF THE CUT AND TAPE OFFThermostat Control Circuit ATTACH THERMOSTAT TO SUBBASE TO TURN THERMOSTAT OFF BEFigure 7. Attaching thermostat to subbase SYSTEM CONFIGURATION SET OPTION SWITCHES2.Two Compressor Split System Figure 8. Back of thermostat5.Automatic Changeover from Heat to Cool CHECK THERMOSTAT OPERATION FAN OPERATIONHEATING SYSTEM OPERATION MING YOUR THERMOSTATCOOLING SYSTEM OPERATION MING YOUR THERMOSTATLOCKOUT BYPASS OPTION COMPRESSOR LONG TERM CYCLE PROTECTIONCOMPRESSOR SHORT TERM CYCLE PROTECTION pressOPERATING YOUR THERMOSTAT Use SYSTEM to turn the thermostat OFFFigure 9. Removing thermostat from subbase PARTS OF THE THERMOSTAT Figure 10. Attaching thermostat to subbaseThe Back of the Thermostat Body ATING FEATURES to turn thermostat OFF beforeThe Display replaced. The word BAT will be displayed con The Thermostat Buttons and Lights 10 Used withPage OPERATING FEATURES AUTOMATIC CHANGEOVER ON If the automatic changeover feature is enabled and you wish to disable it, press•TWO HOUR TEMPERATURE OVERRIDE — wall, and useTo adjust HEAT anticipation, press • F/C CONVERTIBILITY — Press TIME andto increase the cycle time. If the heat • LOW BATTERY INDICATOR — The word BAT • COMPRESSOR SHORT CYCLE PROTECCOOL COOL or HEATuntil FAN constant fan, pressuntil FAN displayedPROGRAMMING YOUR THERMOSTAT PLANNING FOR YOUR NEEDS4a. What time does the building become vacant? IN YOUR HOMEfactory preset program your needs, simply pressENTERING YOUR PROGRAM programming. BE SURE TO PRESSHeating/Cooling Schedule Plan WEEKDAY 5 DAYWEEKEND 2 DAY MOR HEATSAMPLE Heating/Cooling Schedule Plan Set Current Time and Day 4. Press and hold eitheruntil you 5. Presswant to stop programming at any time, simply press Enter Cooling Program TO TURN THERMOSTAT OFF BEFORE REATTACHING TO SUBBASE CHECK YOUR PROGRAMMING 6. PressQUESTIONS AND ANSWERS until you return to the point where yougram. See PROGRAMMING YOUR THERMO- STAT GRAMMING YOUR THERMOSTATthermostat immediately, press SYSTEM until OFF is displayed and replace the thermostat onthe wall. Then press tem operation, and pressto begin the ING YOUR THERMOSTATIf the outside temperature is below 50F, DO ING YOUR THERMOSTATERATING YOUR THERMOSTAT MOSTAT MING YOUR THERMOSTATMOSTAT NOTES NOTES White-RodgersDivision, Emerson Electric Co Attn: Technical Service Department9797 Reavis Road St. Louis, MO Part No. 37-5414A