Manuals / White Rodgers / Household Appliance / Thermostat

White Rodgers 1F92W-51 manual

Models: 1F92W-51

1 52

Page 27

18EMER light indicates that the system is in the emergency mode (the heat pump compressor is off and the auxiliary system is maintaining

setpoint temperature — there is a 5 to 10 minute startup delay on the first emergency cycle). AUX light indicates that the auxiliary system is operating.

				16	17			18
							EMER.
5 DAY	FAN							AUX.
								AUX.
7	SYSTEM		TIME	SET		VIEW		HOLD
7	HEAT-OFF-COOL-AUTO		FWD	CLOCK		PRGM		TEMP
8		FAN	TIME	SET		RUN		ADV
8	ON	- AUTO	BACK	DAY		PRGM		PRGM
		9	10	11	12	13	14	15

Page 27

Image 27

Contents

WHITE-RODGERS INSTALLATION &1F92W-51 OPERATION GUIDEAbout Your New Thermostat YOUR NEW THERMOSTAT’S In This GuideTHE THERMOSTAT’S SPECIFICATIONS INSTALLING YOUR THERMOSTATYOUR NEW THERMOSTAT’S FEATURES Do not exceed the specification ratings PRECAUTIONSShipping Temperature Range THE THERMOSTAT’S SPECIFICATIONSSetpoint Temperature Range Operating Ambient Temperature RangeSELECT THERMOSTAT LOCATION INSTALLING YOUR THERMOSTATNEW INSTALLATION ROUTE WIRES TO LOCATIONFigure 1. Routing thermostat wires THE WALL REPLACEMENT INSTALLATIONTABLE 1. WIRE IDENTIFICATION LABELS REMOVE OLD THERMOSTATOLD THERMOSTAT TABLE 2. TERMINAL REFERENCELABEL NEW THERMOSTATATTACH SUBBASE TO WALL Figure 3. Subbase SYSTEM THERMOSTATCUT AND TAPE OFF IF SAFETY CIRCUITS ARE IN ONLY ONE OF THESYSTEM WITH NO SAFETY CIRCUITS SYSTEMS, REMOVE THE TRANSFORMER OF THEThermostat Control Circuit ATTACH THERMOSTAT TO SUBBASE TO TURN THERMOSTAT OFF BEFigure 7. Attaching thermostat to subbase Figure 8. Back of thermostat SYSTEM CONFIGURATIONSET OPTION SWITCHES 2.Two Compressor Split System5.Automatic Changeover from Heat to Cool MING YOUR THERMOSTAT CHECK THERMOSTAT OPERATIONFAN OPERATION HEATING SYSTEM OPERATIONMING YOUR THERMOSTAT COOLING SYSTEM OPERATIONpress LOCKOUT BYPASS OPTIONCOMPRESSOR LONG TERM CYCLE PROTECTION COMPRESSOR SHORT TERM CYCLE PROTECTIONOPERATING YOUR THERMOSTAT Use SYSTEM to turn the thermostat OFFFigure 9. Removing thermostat from subbase PARTS OF THE THERMOSTAT Figure 10. Attaching thermostat to subbaseThe Back of the Thermostat Body ATING FEATURES to turn thermostat OFF beforeThe Display replaced. The word BAT will be displayed con 10 Used with The Thermostat Buttons and LightsPage OPERATING FEATURES AUTOMATIC CHANGEOVER ON wall, and use If the automatic changeover feature is enabledand you wish to disable it, press •TWO HOUR TEMPERATURE OVERRIDE —To adjust HEAT anticipation, press • F/C CONVERTIBILITY — Press TIME andto increase the cycle time. If the heat COOL or HEAT • LOW BATTERY INDICATOR — The word BAT• COMPRESSOR SHORT CYCLE PROTEC COOLdisplayed until FANconstant fan, press until FANPLANNING FOR YOUR NEEDS PROGRAMMING YOUR THERMOSTATIN YOUR HOME 4a. What time does the building become vacant?your needs, simply press factory preset programprogramming. BE SURE TO PRESS ENTERING YOUR PROGRAMMOR HEAT Heating/Cooling Schedule PlanWEEKDAY 5 DAY WEEKEND 2 DAYSAMPLE Heating/Cooling Schedule Plan 5. Press Set Current Time and Day4. Press and hold either until youwant to stop programming at any time, simply press Enter Cooling Program TO TURN THERMOSTAT OFF BEFORE REATTACHING TO SUBBASE 6. Press CHECK YOUR PROGRAMMINGGRAMMING YOUR THERMOSTAT QUESTIONS AND ANSWERSuntil you return to the point where you gram. See PROGRAMMING YOUR THERMO- STATOFF is displayed and replace the thermostat on thermostat immediately, press SYSTEM untilING YOUR THERMOSTAT the wall. Then presstem operation, and press to begin theIf the outside temperature is below 50F, DO ING YOUR THERMOSTATERATING YOUR THERMOSTAT MING YOUR THERMOSTAT MOSTATMOSTAT NOTES NOTES Part No. 37-5414A White-RodgersDivision, Emerson Electric CoAttn: Technical Service Department 9797 Reavis Road St. Louis, MO