Attach Thermostat to Subbase, Use | White Rodgers 1F92W-51 instruction

ATTACH THERMOSTAT TO SUBBASE

WE RECOMMEND THAT YOU SET OPTION SWITCHES TO DESIRED POSITION BEFORE AT- TACHING ON SUBBASE (see OPERATION). WE

ALSO RECOMMEND THAT YOU PROGRAM THE THERMOSTAT WITH BATTERY INSTALLED BE- FORE ATTACHING ON SUBBASE (see OPERA- TION section for programming instructions).

USE	SYSTEM	TO TURN THERMOSTAT OFF BE-
	HEAT-OFF-COOL-AUTO

FORE ATTACHING TO WALL. FAILURE TO TURN OFF THERMOSTAT BEFORE ATTACHING TO WALL MAY CAUSE EQUIPMENT DAMAGE DUE TO RAPID COMPRESSOR CYCLING.

To attach thermostat to subbase, line up the plastic snap guides at the top of the thermostat and the 4 connector pins on the thermostat with the connec- tors near the top right section of the subbase (when viewed from the front). Gently pivot the thermostat down until the 9-pin connectors and the plastic

snaps lock into place (see fig. 7). Be gentle when attaching thermostat. If the thermostat does not seem to be attaching to the subbase easily, make sure that the connector pins and plastic snaps are properly aligned, and that excess wire is pushed into the wall. Damage to the thermostat may occur if force is used.

ENGAGE TWO UPPER GUIDES; PIVOT DOWN

Figure 7. Attaching thermostat to subbase

16

Image 16

White Rodgers 1F92W-51 manual Attach Thermostat to Subbase, Use, To Turn Thermostat OFF be

Contents

1F92W-51 About Your New Thermostat THERMOSTAT’S Specifications Installing Your Thermostat Your NEW THERMOSTAT’SOperating Your Thermostat Programming Your Your NEW THERMOSTAT’S Features Precautions THERMOSTAT’S Specifications AccessoriesElectrical Data Thermal Data Staging Data NEW Installation Installing Your ThermostatRoute Wires to Location Routing thermostat wires Replacement Installation Wire Identification LabelsRemove OLD Thermostat WallPage Attach Subbase to Wall Subbase Typical wiring diagram for single transformer systems Depending on System Require Heat Pump System USE Attach Thermostat to SubbaseTo Turn Thermostat OFF be SET Option Switches System ConfigurationTwo Compressor Split System Switch #1 on Switch #2 on Check Thermostat Operation FAN OperationHeating System Operation Ming Your Thermostat Cooling System Operation Compressor Short Term Cycle Protection Lockout Bypass OptionPress Operating Your Thermostat Use System to turn the thermostat OFF Parts of the Thermostat Back of the Thermostat Body Removing thermostat from the wall to re- place the battery Ating FeaturesUse To turn thermostat OFF before System Time SET View Hold Thermostat Buttons and Lights Used with System Time SET View Hold Operating Features Automatic Changeover on TWO Hour Temperature Override Automatic Changeover OFF Convertibility Press Time To adjust Heat anticipation, pressTo increase the cycle time. If the heat LOW Battery Indicator The word BAT Compressor Short Cycle ProtecCool Cool or Heat Until FAN Programming Your Thermostat Planning for Your Needs Your Home Factory preset program Your needs, simply press Programming. be Sure to Press Entering Your ProgramTurn Thermostat OFF Before REATTACH- ING to Subbase Heating/Cooling Schedule Plan Weekday 5 DAY Weekend 2 DAY Sample MOR Heat Set Current Time and Day Press and hold eitherUntil you Enter Heating Program Want to stop programming at any time, simply press Enter Cooling Program Fore Reattaching to Subbase Check Your Programming Questions and Answers Until you return to the point where youHow can I permanently change a part of my program? Gramming Your Thermostat Why can’t I program the thermostat in the Auto mode? What can cause the thermostat display to freeze or go blank? ING Your Thermostat Mostat Erating Your Thermostat Why is the system turning on and off so frequently seldom? Maintains programming, press System until Page Page Part No -5414A