Safety Rules
WARNING
READ THESE RULES AND THE INSTRUCTIONS CAREFULLY. FAILURE TO FOLLOW THESE RULES AND INSTRUCTIONS COULD CAUSE A MALFUNCTION OFTHE FURNACE. THIS COULD
RESULT tN DEATH, SERIOUS BODILY INJURY, AND/OR PROPERTY DAMAGE.
INSTALLATION MUST CONFORM TO LOCAL CODES. IN THE ABSENCE OF LOCAL CODES, INSTALLATION MUST CONFORM WITH THE NATIONAL FUEL GAS CODE, ANSI Z223.1. THE APPLIANCE, WHEN INSTALLED, MUST BE ELECTRICALLY CONNECTED AND GROUNDED IN ACCORDANCE WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES, WITH THE CURRENT NATIONAL ELECTRICAL CODE ANSI/NFPA NO. 70.
IN CANADA
1.INSTALLATION MUST CONFORM TO LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES, THE CURRENT CAN/CGA B149 IN-
STALLATION CODE.
2.THE APPLIANCE, WHEN INSTALLED, MUST BE ELECTRICALLY CONNECTED AND GROUND-
ED IN ACCORDANCE WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES, WITH THE CURRENT CSA C22.1 CANADIAN ELEC- TRICAL CODE.
3.FIELD CONVERSIONS FOR HIGH ALTITUDE ARE NOT PERMITTED IN CANADA.
4.REFERENCE IS MADE IN THIS MANUAL REGARDING GAS TYPE AS L.RG. BE ADVISED THAT L.RG. IS NOT AVAILABLE IN CANADA, REFER TO PROPANE/L.R GAS.
1, USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.
2.DO NOT install this furnace in an alcove.
3.DO NOT install these furnaces in a travel trailer, recreational vehicle or mobile home.
4.MAINTAIN all clearances specified in section "Locating Wall Furnace and Thermostat" and "Vent Installation."
5.BE SURE furnace is for type of gas to be used. Check the rating plate by the gas valve in the lower cabinet. Do not change it to use other gases. Unsafe opera-
tion could result and could cause bodily injury and death.
6, For Natural gas, the minimum inlet gas supply pressure for the purpose of input adjustment is 5" col- umn. The maximum inlet gas supply pressure is 7" water column.
For L.R gas, the minimum inlet gas supply pressure for the purpose of input adjustment is 11" water col-
umn. The maximum inlet gas supply pressure is 13" water column.
ANY SAFETY SCREEN, GUARD OR PARTS RE- MOVED FOR SERVICING AN APPLIANCE MUST BE REPLACED PRIOR TO OPERATING THE AP- PLIANCE TO AVOID PROPERTY DAMAGE, BODILY INJURY OR DEATH.
,INSTALL the furnace vent directly to the outdoors, so
that harmful gasses will not collect inside the building. Follow the venting instructions for your type installa- tion exactly. Use only the type and size of vent pipe and fittings specified.
9.BE SURE to provide for adequate combustion and ventilation air. See page 7. The flow of this air to the furnace must not be blocked.
10.NEVER vent flue gases into another room, a fireplace
or any space inside a building. This could cause pro- perry damage, bodily injury or death.
11.NEVER test for gas leaks with an open flame. Use soap suds to check all gas connections. This will avoid the possibility of fire or explosion.
12.ALLOW furnace to cool before servicing. Always shut
off electricity and gas to furnace when working on it. This will prevent any electrical shocks or burns.
13.DUE TO HIGH TEMPERATURES, locate the furnace out of traffic and away from furniture and draperies.
14.ALERT children and adults to the hazards of high sur- face temperature and to keep away to avoid burns or clothing ignition.
15.CAREFULLY supervise young children when they are in the same room with the furnace.
16.DO NOT place clothing or other flammable material on or near furnace.
17.INSTALLATION and REPAIR must be done by a quali- fied service person. The appliance should be inspected before use and at least annually by a professional serv- ice person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that control ,compartments, burners and circulating air passages be kept clean.
18.BEFORE INSTALLING: To avoid electrical shock, turn off electrical circuits that pass through the wall where you are going to install the furnace.
19.BE AWARE of good safety practices by wearing per- sonal protective equipment such as gloves and safe- ty glasses to avoid being injured by sharp metal edges
in or around furnace and while cutting or drilling holes in wood and or sheet metal,
20.CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
I WARNING
DO NOT USE THIS HEATER IF ANY PART HAS BEEN UNDER WATER. IMMEDIATELY CALL A QUALIFIED SERVICE TECHNICIAN TO INSPECT THE HEATER AND TO REPLACE ANY PART OF THE CONTROL SYSTEM
AND ANY GAS CONTROL WHICH HAS BEEN UNDER WATER.
