Manuals / Woods Equipment / Lawn and Garden / Lawn Mower

Woods Equipment 7000, 7192, 7194, 7195, 7200, 7205 manual Install Blades, Sharpen Blades, 1-32

Models: 7000, 7192, 7194, 7195, 7200, 7205

1 50

Download 50 pages 29.52 Kb

Page 19

Install Blades

OWNER SERVICE Cont’d

Install Blades

CAUTION

Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

IMPORTANT

■We recommend you install a new Nylok blade bolt when you replace the blade.

■Do not substitute any bolt for the special blade bolt. It is self-locking, meeting the non-loos- ening requirements for this application.

Refer to Figure 7.

1.Install spindle lock wrench (5) through belt shield

(3) and into holes in spindle pulley as shown Figure 7.

2.Install shoulder washer (2) if removed, small end up. Make sure blade cutting edge is positioned to lead in a clockwise rotation, as viewed from top of mower.

3.Install two cup washers (7) on bolt (8). Install washer (6) and blade (1) on bolt. Remember that bolt

(8) has right hand threads; install bolt and blade assembly into spindle.

4.Torque bolt to 170 lbs.-ft. Remove spindle lock wrench from pulley and shield.

Sharpen Blades

IMPORTANT

■When sharpening blades be sure to balance them. Unbalanced blades will cause excessive vibration which can damage blade spindle bear- ings. Vibration may also cause structural cracks in mower components.

1.Remove blades.

2.Always sharpen both ends at the same time to maintain balance. Follow original sharpening pattern. Do not sharpen blade to a razor edge. Leave from 1/32" to 1/16" blunt edge. Do not sharpen back side.

Follow Original Pattern

CD3411

Maintain Corner

1-32"

Figure 8 Blade Sharpening

MAN0137 (9/14/01)	Owner Service 17

Image 19

Woods Equipment 7000, 7192, 7194, 7195, 7200, 7205 manual Install Blades, Sharpen Blades, Follow Original Pattern, 1-32

Contents

MAN0137 C360 Undermount Mower mounting toCub Cadet Tractor Models 7000, 7192, 7194, 7195, 7200 Mounting KitModel Date of Purchase Serial Number see Safety Decal section for locationTO THE DEALER TO THE OWNERIntroduction TABLE OF CONTENTS2 Introduction SPECIFICATIONSGENERAL INFORMATION TRAINING SafetySAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVEDATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED 4 SafetyTRANSPORTATION SAFETY RULESSAFETY RULES MAINTENANCESTORAGE SafetyReplace Immediately If Damaged 6 SafetySAFETY & INSTRUCTIONAL DECALS 2000 RPMSAFETY & INSTRUCTIONAL DECALS SafetySHIELD MISSING TO AVOID SERIOUS INJURY OR DEATHOPERATION 8 OperationOperation Cont’d Adjust Cutting HeightFront lift stop assembly OperationOperation Cont’d Operation Safety10 Operation Remove Mower from TractorOperation Cont’d Operating TechniquesOperating Tips OperationUneven Terrain 12 OperationOperation Cont’d OWNER SERVICE Owner ServiceDrive Shaft Lubrication 14 Owner ServiceOWNER SERVICE Cont’d LubricationFREQUENCY Owner ServiceOWNER SERVICE Cont’d DESCRIPTIONOWNER SERVICE Cont’d 16 Owner ServiceBLADE SERVICING Remove BladesMaintain Corner Install BladesSharpen Blades Follow Original PatternReplace Belt 18 Owner ServiceOWNER SERVICE Cont’d Spindle Repair Tips Dealer ServiceDEALER SERVICE BLADE SPINDLE Remove Blade SpindleDEALER SERVICE Cont’d 20 Dealer ServiceAssemble Blade Spindle Left Front Lift Stop Install Blade SpindleReplace Oilite Bushings Left Rear Rockshaft Mount Oilite BushingDEALER SERVICE Cont’d 22 Dealer ServiceUNIVERSAL JOINT REPAIR Disassemble U-JointDealer Service Disassemble U-Joint cont’dDEALER SERVICE Cont’d DEALER SERVICE Cont’d 24 Dealer ServiceGEARBOX MAINTENANCE Assemble U-JointDealer Service Install SealRemove Gearbox Repair Gearbox Leak15/16DB2938 26 Dealer ServiceInstall Drive Pulley 1-7/8TROUBLE SHOOTING Trouble ShootingTROUBLE SHOOTING MOWING CONDITIONS Trouble Shooting Cont’d TROUBLE SHOOTING BELT CONDITIONS 28 Trouble ShootingInstall Front Mounting Plate AssemblyASSEMBLY Adjust Wheel Stop BoltAssembly Instructions Cont’d 30 AssemblyInstall Left Front Lift Stop Assembly Install Right Front Lift StopAssembly Instructions Cont’d Install Right Rear Rockshaft 32 AssemblyAssembly Instructions Cont’d Assembly Install Left Rear RockshaftAssembly Instructions Cont’d Assembly Instructions Cont’d 34 AssemblyInstall Transport Lock-Up 8 5 7Assembly Assemble Mechanical Lift Pull RodAssembly Instructions Cont’d Assembly Instructions Cont’d 36 AssemblyPREPARE MOWER Install Discharge Chute Install Mounting Channel & Lift BarAssembly Instructions Cont’d Install Rear Lift BarsInstall Front Caster Wheel AssemblyAssembly Instructions Cont’d 38 AssemblyInstall Rear Gauge Wheel Install Mid-PTO DriveshaftAssembly Instructions Cont’d Install Gearbox Vent PlugInstall Rear Lift Stop AssemblyAttach Mower to Tractor 40 AssemblyAssembly Instructions Cont’d Assembly Adjust Mower with Mechanical LiftAssembly Instructions Cont’d Assembly Instructions Cont’d 42 AssemblyPRE-DELIVERY CHECK LIST DELIVERY CHECK LISTTo locate your nearest dealer PARTSParts CONTACT YOUR WOODS DEALER TO ORDER PARTS52 Appendix BOLT TORQUE CHARTSAE SERIES A TORQUE CHART CHARTAppendix BOLT SIZE CHARTABBREVIATIONS Woods Equipment Company WARRANTYReplacement Parts For All Models Except Mow’n Machines Woods Equipment Company WARRANTYAll Models Except Mow’n Machines MAN0137 PART NUMBER