Contents | Woodstock W1754 specs

Contents

INTRODUCTION

INTRODUCTION	2
Woodstock Technical Support	2
Machine Specifications	3
SAFETY	5
Standard Safety Instructions	5
Additional Safety Instructions for Planers ...	7
ELECTRICAL	8
220V Operation	8
Electrical Specifications	8
SETUP	9
Unpacking	9
Items Needed for Setup	9
Inventory	9
Machine Placement	10
Lifting Planer	10
Cleaning Machine	11
Extension Wings	12
Handwheel, Dust Hood & Caster	13
Gearbox Oil Level	14
Connecting to Power	14
Test Run	15
Recommended Adjustments	16
Tighten V-Belts	16
OPERATIONS	17
General	17
Basic Operation	17
Operation Tips	18
Feed Speed	19
Bed Rollers	20
ACCESSORIES	21
Planer Accessories	21

MAINTENANCE	23
General	23
Cleaning	23
Maintenance Schedule	23
V-Belts	24
Lubrication	25
SERVICE	26
General	26
Inspecting Knives	26
Setting/Replacing Knives	27
Chain Tension	28
Table Parallelism	29
Rollers, Breaker & Pressure Bar Heights ....	31
Spring Tension	34
Chip Deflector Positioning	35
Scale Calibration	35
Anti-Kickback Fingers	36
Pulley Alignment	37
W1754 Electrical Components	38
W1754 Wiring Diagram	39
Troubleshooting	40
Headstock Assembly Parts Breakdown	42
Headstock Assembly Parts List	43
Gearbox Parts Breakdown	45
Gearbox Parts List	46
Base Breakdown	47
Base Parts List	48
Table Breakdown & List	49
Columns Breakdown	50
Columns Parts List	51
Labels & Cosmetic Parts	52

SAFETY ELECTRICAL

SET UP OPERATIONS MAINTENANCE SERVICE

USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!

PARTS

Image 3

Woodstock W1754 owner manual Contents

Contents

Planer with Mobile Base Page Contents Woodstock Technical Support Introduction Introduction Controls and Features Standard Safety Instructions Safety Always Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers Electrical Specifications Electrical220V Operation Inventory SetupItems Needed for Setup Unpacking Machine Placement Lifting PlanerHardware and Tools Not Shown These items are coated and must be cleaned Cleaning Machine Extension wing fasteners Leveling controls Extension Wings To install the handwheel, do these steps To install the caster and foot pedal, do these stepsHandwheel, Dust Hood Caster Connecting to Power Gearbox Oil LevelTo check the gearbox oil level, do these steps To perform a test run, do these steps Test Run Tighten V-Belts Recommended Adjustments Basic steps of operating the planer are as follows OperationsGeneral Basic Operation Operation Tips Feed control knob positions Feed Speed Adjustment Height Range 002-0.020 To adjust the bed rollers, do these stepsBed Rollers Planer Accessories Accessories Operations Maintenance CleaningMaintenance Schedule To adjust/replace the V-belts, do these steps BeltsPulley Alignment on Lubrication Service Inspecting KnivesTo inspect the knives, do these steps To set the knives, do these steps Setting/Replacing Knives Chain Tension To adjust the chain tension, do these steps Maximum Allowable Tolerances Table Parallelism Table micro-adjustment screws To adjust the table parallelism, do these steps Distance Below Knife Edge at *BDC Rollers, Breaker Pressure Bar Heights Location Service Spring Tension To adjust roller spring tension, do these steps Scale Calibration Loosen the chip deflector mounting bolts see FigureTo calibrate the scale, do these steps Anti-kickback fingers Anti-Kickback Fingers Example of checking belt Alignment Pulley Alignment Motor junction box W1754 Electrical Components W1754 20 Planer With Mobile Base Problem Possible Cause Corrective Action Troubleshooting Cutting Headstock Assembly Parts Breakdown PART# Description Headstock Assembly Parts List Cutterheadpulley Gearbox Parts Breakdown Gearbox Parts List Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Comments Warranty Registration BOX BELLINGHAM, WA