Machine Specifications | Woodstock W1770 manual

W1770 21" Bandsaw w/Foot Brake

MACHINE

SPECIFICATIONS

Phone #: (360) 734-3482 • Online Tech Support: tech-support@shopfox.biz • Web: www.shopfox.biz

MOdEl W1770

21" 5HP HEAvy-duTy bANdSAW w/FOOT bRAKE

Motor
Type	TEFC Capacitor Start Induction
Horsepower	5 HP
Voltage	220V
Phase	Single
Amps	22A
Speed	1725 RPM
Cycle	60 Hz
Number Of Speeds	1
Power Transfer	Belt Drive
Bearings	Shielded and Permanently Lubricated
Main Specifications
Operation Information
Blade Speed	4600 FPM
Table Tilt	Left 5°, Right 45°
Cutting Capacities
Maximum Cutting Height	14"
Throat Capacity Left of Blade	20"
Blade Information
Standard Blade Length	165"
Blade Width Range	1/4"–13/8"
Blade Guides	Ball Bearing
Table Information
Table Length	291⁄2"
Table Width	203⁄4"
Table Thickness	17⁄8"
Floor to Table Height	351⁄2"
Fence Information
Locks in Front	Yes
Locks in Rear	No
Adjustable for Blade Lead	No
Resaw Fence Plate Height	6"
Overall Dimensions
Weight	594 lbs.
Length	391/2"
Width	285/8"
Height	78"
Foot Print (Length/Width)	215/8" x 331/2"

INTRODUCTION

-3-

Image 5

Woodstock W1770 manual Machine Specifications

Contents

OWNERS MANUAL Page Contents Functional Overview Woodstock Technical Support Machine Specifications W1770 21 Bandsaw w/Foot Brake Controls and Features Safety Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Bandsaws Use push sticks whenever possible Use push blocks when necessary Extension Cords Electrical Specifications220V Operation Description Qty Items Needed for SetupUnpacking Hardware and Tools InventoryBox Inventory Figure Qty Cleaning Machine Machine Placement Lifting the bandsaw 2x4 Lifting & Moving Bolting to Concrete Floors Mounting to Shop Floor Guide Post Handwheel To install the fence, do these stepsFence Changes in the blade tension may change the blade tracking Blade TrackingTo center track the blade, do these steps To set the positive stop, do these steps Positive Stop To connect the dust collection hoses, do these steps Dust Collection To test run the machine, do these steps Test Run Resetting the switch To tension the bandsaw blade, do these steps Adjusting Blade Guide Bearings onTensioning Blade To adjust the upper blade guides, do these steps Adjusting Blade Guide Bearings To adjust the upper support bearing, do these steps Adjusting Support Bearings Blade aligned 0.016 away from Bearing edge Lower support bearing controls To adjust the lower support bearing, do these steps Cap screws securing table to Trunnion Aligning Table Cap screws securing rail to Aligning Fence Calibrating Miter Gauge Calibrating Fence PointerTo calibrate the pointer, do these steps To calibrate the miter gauge, do these steps Enough to slide on the resaw fence To install the resaw fence, do these steps Control Panel GeneralBasic Controls Rear Controls Figure Front Controls Figure Cutting wood with minor Warping Workpiece Inspection Bandsaw is capable of performing the following cuts Cutting OverviewBasic Cutting Tips Guide Post Foot Brake Blade Lead Fine Tune TrackingCorrecting Blade Lead Aligning Table on Page 27 and Aligning Fence on To shift the table, do these steps Rip Cutting Table TiltTo tilt the table, do these steps To make a rip cut, do these steps Resawing CrosscuttingTo make a 90˚ crosscut, do these steps To resaw a workpiece, do these steps To complete a stacked cut, do these steps Cutting CurvesStacked Cuts Tooth Style Blade LengthBlade Width Blade Care Tooth PitchBlade Breakage Most common causes of blade breakage are To replace a blade, do these steps Blade ChangesTo remove a blade, do these steps Table & Base CleaningBrushes Lubrication Lubricant Frequency Quantity Tension Adjustment AssemblyBlade Guide Rack and Pinion To lubricate the trunnion, do these steps Table Tilt Rack and Pinion AssemblyTrunnion Tools Needed Checking and Tensioning BeltsChecking V-Belts Follow Steps 1-2 in Checking V-Belts on Tensioning V-BeltsReplacing V-Belts To adjust the tension lever, do these steps Adjusting Tension Lever To adjust the brushes, do these steps Adjusting Wheel Blade Brushes Components and Hardware Needed Replacing Brake ShoeTo replace the brake shoe Follow Steps 1-4 in Replacing V-Belts on Checking Coplanarity Aligning Wheels Gauge Shimming Upper Wheel To adjust the lower wheel, do these steps Adjusting Lower Wheel Electrical Components Power supply terminal box See Figure Wiring DiagramSee , Motor & Electrical Troubleshooting Cutting Tips on Machine Operations Labels & Cosmetic Parts Parts Blade Guides-Cover Breakdown Parts Guide Post-Table Tilt Breakdown Table-Trunnion Breakdown Body Breakdown Capacitor Cover Body Parts List Motor Cord 12AWG X 3C Resaw Fence Breakdown Comments Warranty Registration Woodstock international inc. p.o. box Bellingham, wa Warranty