Box Inventory Figure Qty, Hardware and Tools | Woodstock W1770

W1770 21" Bandsaw w/Foot Brake

SETUP

Inventory

The following is a description of the main components shipped with the Model W1770. Lay the components out to inventory them.

Note: If you can't find an item on this list, check the mounting location on the machine or examine the pack- aging materials carefully. Occasionally we pre-install cer- tain components for safer shipping.

Box Inventory (Figure 9)		Qty
A.	Guide Post Handwheel	1
B.	Miter Gauge	1
C.	Fence	1
D.	Resaw Fence	1
Hardware and Tools
•	Hex Wrenches 5, 6mm	1 EA
•	Wrenches 10/13, 17/19	1 EA
•	Flat Washer 8mm (Resaw Fence)	1
•	Resaw Fence Lock Handle (Resaw Fence)	1
•	Moving Plate (Resaw Fence)	1
•	Eye Bolts (Lifting)	2

AD

B

C

Figure 9. W1770 inventory.

SUFFOCATION HAZARD!

Immediately discard all

plastic bags and pack-

ing materials to elimi- nate choking/suffocation hazards for children and animals.

-12-

Image 14

Woodstock W1770 manual Box Inventory Figure Qty, Hardware and Tools

Contents

OWNERS MANUAL Page Contents Woodstock Technical Support Functional Overview Machine Specifications W1770 21 Bandsaw w/Foot Brake Controls and Features Safety Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Bandsaws Use push blocks when necessary Use push sticks whenever possible Extension Cords Electrical Specifications220V Operation Description Qty Items Needed for SetupUnpacking Hardware and Tools InventoryBox Inventory Figure Qty Machine Placement Cleaning Machine Lifting & Moving Lifting the bandsaw 2x4 Mounting to Shop Floor Bolting to Concrete Floors Guide Post Handwheel To install the fence, do these stepsFence Changes in the blade tension may change the blade tracking Blade TrackingTo center track the blade, do these steps Positive Stop To set the positive stop, do these steps Dust Collection To connect the dust collection hoses, do these steps Test Run To test run the machine, do these steps Resetting the switch To tension the bandsaw blade, do these steps Adjusting Blade Guide Bearings onTensioning Blade Adjusting Blade Guide Bearings To adjust the upper blade guides, do these steps Adjusting Support Bearings To adjust the upper support bearing, do these steps Blade aligned 0.016 away from Bearing edge To adjust the lower support bearing, do these steps Lower support bearing controls Aligning Table Cap screws securing table to Trunnion Aligning Fence Cap screws securing rail to To calibrate the pointer, do these steps Calibrating Fence PointerCalibrating Miter Gauge To calibrate the miter gauge, do these steps To install the resaw fence, do these steps Enough to slide on the resaw fence Control Panel GeneralBasic Controls Front Controls Figure Rear Controls Figure Workpiece Inspection Cutting wood with minor Warping Bandsaw is capable of performing the following cuts Cutting OverviewBasic Cutting Tips Foot Brake Guide Post Correcting Blade Lead Fine Tune TrackingBlade Lead Aligning Table on Page 27 and Aligning Fence on To shift the table, do these steps To tilt the table, do these steps Table TiltRip Cutting To make a rip cut, do these steps To make a 90˚ crosscut, do these steps CrosscuttingResawing To resaw a workpiece, do these steps To complete a stacked cut, do these steps Cutting CurvesStacked Cuts Tooth Style Blade LengthBlade Width Blade Breakage Tooth PitchBlade Care Most common causes of blade breakage are To replace a blade, do these steps Blade ChangesTo remove a blade, do these steps Brushes CleaningTable & Base Lubrication Lubricant Frequency Quantity Tension Adjustment AssemblyBlade Guide Rack and Pinion To lubricate the trunnion, do these steps Table Tilt Rack and Pinion AssemblyTrunnion Tools Needed Checking and Tensioning BeltsChecking V-Belts Follow Steps 1-2 in Checking V-Belts on Tensioning V-BeltsReplacing V-Belts Adjusting Tension Lever To adjust the tension lever, do these steps Adjusting Wheel Blade Brushes To adjust the brushes, do these steps To replace the brake shoe Replacing Brake ShoeComponents and Hardware Needed Follow Steps 1-4 in Replacing V-Belts on Aligning Wheels Checking Coplanarity Shimming Upper Wheel Gauge Adjusting Lower Wheel To adjust the lower wheel, do these steps Power supply terminal box Electrical Components See Figure Wiring DiagramSee , Troubleshooting Motor & Electrical Machine Operations Cutting Tips on Parts Labels & Cosmetic Parts Blade Guides-Cover Breakdown Guide Post-Table Tilt Breakdown Parts Table-Trunnion Breakdown Body Breakdown Body Parts List Capacitor Cover Motor Cord 12AWG X 3C Resaw Fence Breakdown Warranty Registration Comments Woodstock international inc. p.o. box Bellingham, wa Warranty