Labels & Cosmetic Parts | Woodstock W1770 instruction

W1770 21" Bandsaw w/Foot Brake

PARTS

Labels & Cosmetic Parts

Safety labels warn about machine hazards and how to prevent machine damage or injury. The owner of this machine MUST maintain the original location and readability of all labels on this machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www. shopfoxtools.com to order new labels.

2

3 15

14

		5	16
	14	6
	13	7
	12
	11
	10	3
		3	17
		4	17
	9	4	18
	9		18
		8

20

19

23

22

21

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

1	X1770001	MACHINE ID LABEL
2	D3376	SHOP FOX LOGO PLATE
3	X1770003	DISCONNECT POWER LABEL HL
4	XLABEL-05	CLOSE DOOR LABEL
5	XLABEL-17	BLADE CUT DIRECTION LABEL
6	X1770006	BANDSAW BLADE CUT LABEL HL
7	X1770021	BLADE GUIDE ASSEMBLY SCALE
8	X1770008	W1770 MODEL # LABEL
9	X1770009	DECORATIVE BLACK STRIPE
10	XPPAINT-1	SHOP FOX WHITE PAINT
11	X1770011	TABLE MEASUREMENT SCALE
12	XLABEL-04	ELECTRICITY LABEL

13	XLABEL-08H	READ MANUAL LABEL HL
14	XLABEL-06	GLASSES RESPIRATOR LABEL HL
15	X1770015	WHEEL HINGE/STOP BOLT LABEL
16	X1770016	PATENT LABEL
17	XLABEL-04S	ELECTRICITY LABEL (SMALL)
18	X1770018	TABLE TILT HANDWHEEL LABEL
19	X1770019	BLADE ASSEMBLY DIRECTION LABEL
20	X1770020	TENSION ADJUSTMENT LABEL
21	X1770021	MOTOR LABEL
22	X1770022	TABLE LOCK LEVER LABEL	PARTS
23	X1770023	TABLE ANGLE SCALE

-59-

Image 61

Woodstock W1770 manual Labels & Cosmetic Parts

Contents

OWNERS MANUAL Page Contents Functional Overview Woodstock Technical Support Machine Specifications W1770 21 Bandsaw w/Foot Brake Controls and Features Safety Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Bandsaws Use push sticks whenever possible Use push blocks when necessary 220V Operation Electrical SpecificationsExtension Cords Unpacking Items Needed for SetupDescription Qty Box Inventory Figure Qty InventoryHardware and Tools Cleaning Machine Machine Placement Lifting the bandsaw 2x4 Lifting & Moving Bolting to Concrete Floors Mounting to Shop Floor Fence To install the fence, do these stepsGuide Post Handwheel To center track the blade, do these steps Blade TrackingChanges in the blade tension may change the blade tracking To set the positive stop, do these steps Positive Stop To connect the dust collection hoses, do these steps Dust Collection To test run the machine, do these steps Test Run Resetting the switch Tensioning Blade Adjusting Blade Guide Bearings onTo tension the bandsaw blade, do these steps To adjust the upper blade guides, do these steps Adjusting Blade Guide Bearings To adjust the upper support bearing, do these steps Adjusting Support Bearings Blade aligned 0.016 away from Bearing edge Lower support bearing controls To adjust the lower support bearing, do these steps Cap screws securing table to Trunnion Aligning Table Cap screws securing rail to Aligning Fence Calibrating Miter Gauge Calibrating Fence PointerTo calibrate the pointer, do these steps To calibrate the miter gauge, do these steps Enough to slide on the resaw fence To install the resaw fence, do these steps Basic Controls GeneralControl Panel Rear Controls Figure Front Controls Figure Cutting wood with minor Warping Workpiece Inspection Basic Cutting Tips Cutting OverviewBandsaw is capable of performing the following cuts Guide Post Foot Brake Blade Lead Fine Tune TrackingCorrecting Blade Lead Aligning Table on Page 27 and Aligning Fence on To shift the table, do these steps Rip Cutting Table TiltTo tilt the table, do these steps To make a rip cut, do these steps Resawing CrosscuttingTo make a 90˚ crosscut, do these steps To resaw a workpiece, do these steps Stacked Cuts Cutting CurvesTo complete a stacked cut, do these steps Blade Width Blade LengthTooth Style Blade Care Tooth PitchBlade Breakage Most common causes of blade breakage are To remove a blade, do these steps Blade ChangesTo replace a blade, do these steps Table & Base CleaningBrushes Lubrication Blade Guide Rack and Pinion Tension Adjustment AssemblyLubricant Frequency Quantity Trunnion Table Tilt Rack and Pinion AssemblyTo lubricate the trunnion, do these steps Checking V-Belts Checking and Tensioning BeltsTools Needed Replacing V-Belts Tensioning V-BeltsFollow Steps 1-2 in Checking V-Belts on To adjust the tension lever, do these steps Adjusting Tension Lever To adjust the brushes, do these steps Adjusting Wheel Blade Brushes Components and Hardware Needed Replacing Brake ShoeTo replace the brake shoe Follow Steps 1-4 in Replacing V-Belts on Checking Coplanarity Aligning Wheels Gauge Shimming Upper Wheel To adjust the lower wheel, do these steps Adjusting Lower Wheel Electrical Components Power supply terminal box See , Wiring DiagramSee Figure Motor & Electrical Troubleshooting Cutting Tips on Machine Operations Labels & Cosmetic Parts Parts Blade Guides-Cover Breakdown Parts Guide Post-Table Tilt Breakdown Table-Trunnion Breakdown Body Breakdown Capacitor Cover Body Parts List Motor Cord 12AWG X 3C Resaw Fence Breakdown Comments Warranty Registration Woodstock international inc. p.o. box Bellingham, wa Warranty