Front Controls Figure, Rear Controls Figure | Woodstock W1770

W1770 21" Bandsaw w/Foot Brake

Front Controls (Figure 46)

A.Blade Tension Scale: Allows for easy monitoring of blade tension.

B.Blade Tension Handwheel: Tensions blade in gradual increments.

C.Blade Tracking Window: Allows for easy monitoring of blade tracking (refer to Page 36).

D.Fence, Rails, and Miter Gauge: Allows for controlled cutting at various angles.

E.Foot Brake: Cuts power to motor and allows bandsaw blade to be quickly brought to a stop.

A

B

C

D

E

Figure 46. Front controls.

OPERATIONS

Rear Controls (Figure 47)

F.Guide Post Handwheel and Lock Knob: Moves blade guide support quickly to the desired height on the guide post; locks setting (refer to Page 35).

G.Blade Tracking Knob and Lock Lever: Moves and locks blade tracking.

H.Quick Release Blade Tension Lever: Adjusts blade tension for quick blade changes.

I.Table Tilt Handwheel: Tilts the table up to 5º to the left or 45º to the right (refer to Page 38).

J.Table Tilt Lock Lever: Locks or unlocks the table at the current angle.

F

J

G

H

I

Figure 47. Rear controls.

-32-

Image 34

Woodstock W1770 manual Front Controls Figure, Rear Controls Figure

Contents

OWNERS MANUAL Page Contents Woodstock Technical Support Functional Overview Machine Specifications W1770 21 Bandsaw w/Foot Brake Controls and Features Safety Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Bandsaws Use push blocks when necessary Use push sticks whenever possible 220V Operation Electrical SpecificationsExtension Cords Unpacking Items Needed for SetupDescription Qty Box Inventory Figure Qty InventoryHardware and Tools Machine Placement Cleaning Machine Lifting & Moving Lifting the bandsaw 2x4 Mounting to Shop Floor Bolting to Concrete Floors Fence To install the fence, do these stepsGuide Post Handwheel To center track the blade, do these steps Blade TrackingChanges in the blade tension may change the blade tracking Positive Stop To set the positive stop, do these steps Dust Collection To connect the dust collection hoses, do these steps Test Run To test run the machine, do these steps Resetting the switch Tensioning Blade Adjusting Blade Guide Bearings onTo tension the bandsaw blade, do these steps Adjusting Blade Guide Bearings To adjust the upper blade guides, do these steps Adjusting Support Bearings To adjust the upper support bearing, do these steps Blade aligned 0.016 away from Bearing edge To adjust the lower support bearing, do these steps Lower support bearing controls Aligning Table Cap screws securing table to Trunnion Aligning Fence Cap screws securing rail to To calibrate the pointer, do these steps Calibrating Fence PointerCalibrating Miter Gauge To calibrate the miter gauge, do these steps To install the resaw fence, do these steps Enough to slide on the resaw fence Basic Controls GeneralControl Panel Front Controls Figure Rear Controls Figure Workpiece Inspection Cutting wood with minor Warping Basic Cutting Tips Cutting OverviewBandsaw is capable of performing the following cuts Foot Brake Guide Post Correcting Blade Lead Fine Tune TrackingBlade Lead Aligning Table on Page 27 and Aligning Fence on To shift the table, do these steps To tilt the table, do these steps Table TiltRip Cutting To make a rip cut, do these steps To make a 90˚ crosscut, do these steps CrosscuttingResawing To resaw a workpiece, do these steps Stacked Cuts Cutting CurvesTo complete a stacked cut, do these steps Blade Width Blade LengthTooth Style Blade Breakage Tooth PitchBlade Care Most common causes of blade breakage are To remove a blade, do these steps Blade ChangesTo replace a blade, do these steps Brushes CleaningTable & Base Lubrication Blade Guide Rack and Pinion Tension Adjustment AssemblyLubricant Frequency Quantity Trunnion Table Tilt Rack and Pinion AssemblyTo lubricate the trunnion, do these steps Checking V-Belts Checking and Tensioning BeltsTools Needed Replacing V-Belts Tensioning V-BeltsFollow Steps 1-2 in Checking V-Belts on Adjusting Tension Lever To adjust the tension lever, do these steps Adjusting Wheel Blade Brushes To adjust the brushes, do these steps To replace the brake shoe Replacing Brake ShoeComponents and Hardware Needed Follow Steps 1-4 in Replacing V-Belts on Aligning Wheels Checking Coplanarity Shimming Upper Wheel Gauge Adjusting Lower Wheel To adjust the lower wheel, do these steps Power supply terminal box Electrical Components See , Wiring DiagramSee Figure Troubleshooting Motor & Electrical Machine Operations Cutting Tips on Parts Labels & Cosmetic Parts Blade Guides-Cover Breakdown Guide Post-Table Tilt Breakdown Parts Table-Trunnion Breakdown Body Breakdown Body Parts List Capacitor Cover Motor Cord 12AWG X 3C Resaw Fence Breakdown Warranty Registration Comments Woodstock international inc. p.o. box Bellingham, wa Warranty