Manuals / Woodstock / Power Tools / Saw

Woodstock W1770 manual Aligning Wheels, Checking Coplanarity

Models: W1770

1 72

Download 72 pages 31.87 Kb

Page 54

W1770 21" Bandsaw w/Foot Brake

SERVICE

Aligning Wheels
Components and Hardware Needed:	Qty
701⁄4" Long Wood 2x4	1
Tools Needed:
Wrench 17mm	1
Tape Measure	1
Coplanarity Gauge (see Figure 73)	1
Straightedge	1
Fine Ruler	1

Wheel alignment is one of the most critical factors for optimal performance from your bandsaw.

Heat, vibration, wandering, blade wear, tire wear and overall bandsaw wear are considerably decreased when the wheels are properly aligned or “coplanar.”

Coplanar wheels automatically track the blade by balanc- ing it on the crown of the wheel. This is known as copla- nar tracking.

Checking Coplanarity

1.Make the "Coplanarity Gauge" shown in Figure 73.

Note: For best results, straighten the 2x4 with a jointer before cutting.

2.DISCONNECT BANDSAW FROM POWER!

3.Remove the fence and open both wheel covers.

4.Adjust the blade guides away from the blade, loosen blade tension, remove the table insert and pin, then remove the blade.

5.Remove the four trunnion cap screws and the table.

6.Reinstall the blade (Page 43), making sure the guide bearings and support bearings are away from the blade, then tighten your blade to the tension that it will be used during operation.

7.Place your coplanarity gauge up against both wheels in the positions shown in Figure 74.

4"

21"

70¼"

28¼"

1½"

21"

Side View

Figure 73. Dimensions of coplanarity

gauge.

	Coplanarity	Gauge Positions
	Gauge	Gauge Positions
	Gauge
	Tracking
	Knob
	Wheels
	Adjustment
	Hub

Figure 74. Checking for coplanarity.

-52-

Image 54

Woodstock W1770 manual Aligning Wheels, Checking Coplanarity

Contents

OWNERS MANUAL Page Contents Woodstock Technical Support Functional OverviewMachine Specifications W1770 21 Bandsaw w/Foot Brake Controls and Features Safety Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Bandsaws Use push blocks when necessary Use push sticks whenever possibleElectrical Specifications 220V OperationExtension Cords Items Needed for Setup UnpackingDescription Qty Inventory Box Inventory Figure QtyHardware and Tools Machine Placement Cleaning MachineLifting & Moving Lifting the bandsaw 2x4Mounting to Shop Floor Bolting to Concrete FloorsTo install the fence, do these steps FenceGuide Post Handwheel Blade Tracking To center track the blade, do these stepsChanges in the blade tension may change the blade tracking Positive Stop To set the positive stop, do these stepsDust Collection To connect the dust collection hoses, do these stepsTest Run To test run the machine, do these stepsResetting the switch Adjusting Blade Guide Bearings on Tensioning BladeTo tension the bandsaw blade, do these steps Adjusting Blade Guide Bearings To adjust the upper blade guides, do these stepsAdjusting Support Bearings To adjust the upper support bearing, do these stepsBlade aligned 0.016 away from Bearing edge To adjust the lower support bearing, do these steps Lower support bearing controlsAligning Table Cap screws securing table to TrunnionAligning Fence Cap screws securing rail toTo calibrate the pointer, do these steps Calibrating Fence PointerCalibrating Miter Gauge To calibrate the miter gauge, do these stepsTo install the resaw fence, do these steps Enough to slide on the resaw fenceGeneral Basic ControlsControl Panel Front Controls Figure Rear Controls FigureWorkpiece Inspection Cutting wood with minor WarpingCutting Overview Basic Cutting TipsBandsaw is capable of performing the following cuts Foot Brake Guide PostCorrecting Blade Lead Fine Tune TrackingBlade Lead Aligning Table on Page 27 and Aligning Fence onTo shift the table, do these steps To tilt the table, do these steps Table TiltRip Cutting To make a rip cut, do these stepsTo make a 90˚ crosscut, do these steps CrosscuttingResawing To resaw a workpiece, do these stepsCutting Curves Stacked CutsTo complete a stacked cut, do these steps Blade Length Blade WidthTooth Style Blade Breakage Tooth PitchBlade Care Most common causes of blade breakage areBlade Changes To remove a blade, do these stepsTo replace a blade, do these steps Brushes CleaningTable & Base LubricationTension Adjustment Assembly Blade Guide Rack and PinionLubricant Frequency Quantity Table Tilt Rack and Pinion Assembly TrunnionTo lubricate the trunnion, do these steps Checking and Tensioning Belts Checking V-BeltsTools Needed Tensioning V-Belts Replacing V-BeltsFollow Steps 1-2 in Checking V-Belts on Adjusting Tension Lever To adjust the tension lever, do these stepsAdjusting Wheel Blade Brushes To adjust the brushes, do these stepsTo replace the brake shoe Replacing Brake ShoeComponents and Hardware Needed Follow Steps 1-4 in Replacing V-Belts onAligning Wheels Checking CoplanarityShimming Upper Wheel GaugeAdjusting Lower Wheel To adjust the lower wheel, do these stepsPower supply terminal box Electrical ComponentsWiring Diagram See ,See Figure Troubleshooting Motor & ElectricalMachine Operations Cutting Tips onParts Labels & Cosmetic PartsBlade Guides-Cover Breakdown Guide Post-Table Tilt Breakdown PartsTable-Trunnion Breakdown Body Breakdown Body Parts List Capacitor CoverMotor Cord 12AWG X 3C Resaw Fence Breakdown Warranty Registration CommentsWoodstock international inc. p.o. box Bellingham, wa Warranty