Yamaha CDR1000 Applying a Fade In

Applying a Fade In 37

CDR1000—Owner’s Manual

Applying a Fade In

A fade in can be applied at the start of each track using the Fade In function. The length

of the fade in can be set from 1 to 10 seconds in single second steps using the Fade In

parameter. The fade in begins when recording is started from Record Standby mode by

pressing the [PLAY] button, [PAUSE] button, or footswitch.

The Fade In function is off when the Fade In parameter is set to 0.

When the Input Delay function is set, the fade in starts with the digital audio already in

the audio buffer. See “Setting the Input Delay” on page 27 for more information.

Fade In cannot be used with Sync Recording.

The following illustration shows the procedure for applying a fade in.

The Utility Fade In parameter is used to set the fade in time.

1Use the [UTILITY] button to select “FADE IN.”

The UTILITY indicator lights up and the Fade In setting appears on the display.

2Use the [PREV] or [NEXT] button to select a fade in time.

3Press and hold the [UTILITY] button, or press another button to cancel Utility.

A fade in will be applied each time recording is started from Record Standby mode by

pressing the [PLAY] button, [PAUSE] button, or footswitch. See page 29 for more

information of recording.

4To turn off the Fade In function, set the Utility Fade In parameter to 0.

Setting Description

0–10 s Fade in time in seconds (0 = off).

Fade in

Recording

(Recording can also be started

by pressing the [PAUSE] button

or footswitch)

PLAY

Record

Standby

mode

REC

(FADE IN)

UTILITY

Contents

Main E PROFESSIONAL AUDIO CD RECORDER Keep This Manual For Future Reference. Owners Manual PROFESSIONAL AUDIO CD RECORDER POWER FCC INFORMATION (U.S.A.) IMPORTANT 1 2 3 JUISTE GEBRUIK EN BEHANDELING V AN BA TTERIJEN i Important Information Warnings Read the Following Before Operating the CDR1000 ii Handling Discs Cautions Note Contents 1 Introduction Transportation Pad Installation About this Manual CDR1000 Features Page Operating Notes Page 2 Touring the CDR1000 I H G Page 8 Display 88 88 88 88 CDR1000 K L Function Buttons A B C 1 2 3 4 10 D E F G Rear Panel A B C D 12 Remote Controller 14 Block Diagram The Basics 15 3 The Basics Hookup Examples Analog Coaxial AES/EBU Connecting the Power Cord Turning On the Power Using the Transportation Pad Installing the Transportation Pad 18 Loading & Unloading Discs Disc Type & Status Using the Remote Controller Installing the Remote Controllers Batteries Setting the Time Display 20 Monitoring Metering & Peak Hold Setting the Meter Response Rate 4 Playback Playing Discs Pausing Playback Stopping Playback 22 Playback Operation Table Selecting Tracks Selecting Tracks Directly Selecting Indexes 24 Searching Using Repeat Playback One-track Repeat Playback All-track Repeat Playback A-B Repeat Playback 5 Recording Preparing to Record Selecting the Input Source 26 Setting the Sampling Rate Converter Setting the Input Delay 28 Setting the UV22 Setting the Copy Bit Recording 30 Recording Operation Table 31 Recording Operation Table 32 Incrementing Track Numbers Manually Incrementing Index Numbers Manually 34 Using Auto Rec Start & Track Increment Inserting a Two-second Mute Inserting a Mute at the Beginning of a Track 36 Inserting a Mute at the End of a Track Applying a Fade In 38 Applying a Fade Out Sync Recording from CD, MD, or DAT 40 One-track Sync Recording Page 42 All-track Sync Recording Page 44 Finalizing Discs Erasing Discs (CD-RW only) 46 6 Other Functions Selecting the AES/EBU OUT Playback Clock Selecting the AES/EBU OUT Playback Clock 47 Note: If the message OUT OF RANGE appears while monitoring, stop and reset the sampling rate. Wordclock out WORD CLOCK IN (wordclock slave, source: WORD) 00 00 00 00 mYGDAI YGDAI Using Digital Output Thru Using Digital Output Thru 49 CDR1000 (source machine) PARALLEL AES/EBU OUT PARALLEL AES/EBU IN AES/EBU OUT AES/EBU IN Using a Footswitch Disabling the Remote Controller Using the Parallel Port Parallel Port Pin Conguration 52 Troubleshooting Troubleshooting 53 54 Appendix Error Messages If the CDR1000 displays an error message, follow the instructions below. Specifications 55 Specications 56 Analog Input Analog Output Digital Audio Input Digital Audio Output Dimensions 58 Glossary Index A B C D O P R S T