Yamaha CDR1000 Using the Parallel Port

Using the Parallel Port 51

CDR1000—Owner’s Manual

Using the Parallel Port

The PARALLEL port is a general purpose interface that provides remote control access

to various CDR1000 functions, including Play, Pause, Stop, Record Standby, and Track

Increment. By using custom built switches and cables, it can be used for simultaneous

control of several CDR1000s in a multiple disc recording, or disc duplication system.

In addition to receiving trigger signals, the CDR1000 also outputs trigger signals when

the following functions are operated: Play, Pause, and Stop.

The following diagram shows a switching arrangement for the input triggers.

Parallel Port Pin Conﬁguration

The following table shows how the PARALLEL port is wired.

• Input trigger pulses must be 50 ms or longer.

• Each output trigger pulse is 500 ms.

• All outputs are open collector.

Pin I/O Signal

1

Input

Play

2Pause

3Stop

4Record Standby

5Track Increment

6

Output

Play

7Pause

8Stop

9GND

Play Pause Stop

Record

Standby Track

Increment

12345

6789

GND

Contents

Main E PROFESSIONAL AUDIO CD RECORDER Keep This Manual For Future Reference. Owners Manual PROFESSIONAL AUDIO CD RECORDER POWER FCC INFORMATION (U.S.A.) IMPORTANT 1 2 3 JUISTE GEBRUIK EN BEHANDELING V AN BA TTERIJEN i Important Information Warnings Read the Following Before Operating the CDR1000 ii Handling Discs Cautions Note Contents 1 Introduction Transportation Pad Installation About this Manual CDR1000 Features Page Operating Notes Page 2 Touring the CDR1000 I H G Page 8 Display 88 88 88 88 CDR1000 K L Function Buttons A B C 1 2 3 4 10 D E F G Rear Panel A B C D 12 Remote Controller 14 Block Diagram The Basics 15 3 The Basics Hookup Examples Analog Coaxial AES/EBU Connecting the Power Cord Turning On the Power Using the Transportation Pad Installing the Transportation Pad 18 Loading & Unloading Discs Disc Type & Status Using the Remote Controller Installing the Remote Controllers Batteries Setting the Time Display 20 Monitoring Metering & Peak Hold Setting the Meter Response Rate 4 Playback Playing Discs Pausing Playback Stopping Playback 22 Playback Operation Table Selecting Tracks Selecting Tracks Directly Selecting Indexes 24 Searching Using Repeat Playback One-track Repeat Playback All-track Repeat Playback A-B Repeat Playback 5 Recording Preparing to Record Selecting the Input Source 26 Setting the Sampling Rate Converter Setting the Input Delay 28 Setting the UV22 Setting the Copy Bit Recording 30 Recording Operation Table 31 Recording Operation Table 32 Incrementing Track Numbers Manually Incrementing Index Numbers Manually 34 Using Auto Rec Start & Track Increment Inserting a Two-second Mute Inserting a Mute at the Beginning of a Track 36 Inserting a Mute at the End of a Track Applying a Fade In 38 Applying a Fade Out Sync Recording from CD, MD, or DAT 40 One-track Sync Recording Page 42 All-track Sync Recording Page 44 Finalizing Discs Erasing Discs (CD-RW only) 46 6 Other Functions Selecting the AES/EBU OUT Playback Clock Selecting the AES/EBU OUT Playback Clock 47 Note: If the message OUT OF RANGE appears while monitoring, stop and reset the sampling rate. Wordclock out WORD CLOCK IN (wordclock slave, source: WORD) 00 00 00 00 mYGDAI YGDAI Using Digital Output Thru Using Digital Output Thru 49 CDR1000 (source machine) PARALLEL AES/EBU OUT PARALLEL AES/EBU IN AES/EBU OUT AES/EBU IN Using a Footswitch Disabling the Remote Controller Using the Parallel Port Parallel Port Pin Conguration 52 Troubleshooting Troubleshooting 53 54 Appendix Error Messages If the CDR1000 displays an error message, follow the instructions below. Specifications 55 Specications 56 Analog Input Analog Output Digital Audio Input Digital Audio Output Dimensions 58 Glossary Index A B C D O P R S T