Yamaha CDR1000 Troubleshooting

52 Troubleshooting

CDR1000—Owner’s Manual

Troubleshooting

Symptom Advice

Cannot turn on the CDR1000.

Make sure that the power cord is connected to a suitable AC wall out-

let. See “Connecting the Power Cord” on page 16 for more informa-

tion.

Make sure that the CDR1000 POWER switch is set to the ON position.

See “Turning On the Power” on page 16 for more information.

If you still cannot turn on the CDR1000, contact your Yamaha dealer.

Cannot use the remote controller.

Make sure that the batteries are installed correctly. See “Using the

Remote Controller” on page 19 for more information.

Make sure the Utility Remote parameter is set to ON. See “Disabling

the Remote Controller” on page 50 for more information.

Perhaps the batteries need replacing. See “Using the Remote Control-

ler” on page 19 for more information.

The LOCK indicator ﬂashes. A ﬂashing LOCK indicator indicates that the CDR1000 is not locked to

the selected digital input source, in which case recording is not possi-

ble. See “Selecting the Input Source” on page 25 for more information.

Pressing and holding the [UTILITY]

button does not cancel the Utility

functions.

The [UTILITY] button must be pressed for two or more seconds in order

to cancel a Utility functions.

Cannot monitor a signal

connected to the ANALOG IN.

Make sure that the signal is connected to the ANALOG IN connector

correctly and that the input source is set to ANALOG. Engage Record

Standby mode and set the recording level using the REC LEVEL control.

The ANALOG IN signal level is too

low or too high.

Set the ANALOG IN level switch to match the operating level of the

connected equipment (–10 dBV or +4 dB), and set the recording level

using the REC LEVEL control.

Cannot engage Record Standby

mode. Recording is not possible on ﬁnalized CD-R discs. Load another disc.

See “Preparing to Record” on page 25 for more information.

Cannot increment the track

number manually.

The track number cannot be incremented manually when Auto

Rec/Track or Sync Recording is used. See “Incrementing Track Numbers

Manually” on page 32 for more information.

Cannot increment the index

number manually.

The index number cannot be incremented manually when Auto

Rec/Track or Sync Recording is used. See “Incrementing Index Num-

bers Manually” on page 33 for more information.

Using the Auto Rec/Track function,

the track number does not

increment automatically.

If the space between tracks is very short, or the threshold is set too

high, the track number may not increment properly. See “Using Auto

Rec Start & Track Increment” on page 34 for more information.

Using the Auto Rec/Track function,

the track number increments

during quiet passages.

Try raising the threshold to see if that helps. Auto Rec/Track may not

work very well with music that contains many silent passages. See

“Using Auto Rec Start & Track Increment” on page 34 for more infor-

mation.

Recording stops when using the

Auto Rec/Track function.

If the level of the input signal is below the speciﬁed threshold for 20 or

more seconds, recording stops automatically. See “Using Auto Rec Start

& Track Increment” on page 34 for more information.

Cannot insert a mute.

Only one mute can be inserted at the beginning and end of each track.

See “Inserting a Two-second Mute” on page 35 for more information.

Rec Mute cannot be used with All-track Sync Recording. See “Inserting

a Two-second Mute” on page 35 for more information.

Cannot apply a Fade In or Fade

Out.

The Fade In and Fade Out parameters must be set before engaging

Record Standby mode. Fade In and Fade Out cannot be used with Sync

Recording. See “Applying a Fade In” on page 37 and “Applying a Fade

Out” on page 38 for more information.