Yamaha CDR1000 Erasing Discs (CD-RW only)

Erasing Discs (CD-RW only) 45

CDR1000—Owner’s Manual

Erasing Discs (CD-RW only)

CD-RW discs can be erased using the three Erasure functions: Last Track Erase, Disk

Erase, and Initialize Erase. Last Track Erase erases the control data of last recorded track

on unﬁnalized discs. Tracks can be erased one at a time by repeating the Track Erase

function. Disk Erase erases the control data of all tracks quickly, so the entire disc can

be used again. Initialize erases not only the control data of all tracks but the entire pro-

gram area too. Initialize Erase is recommended for discs that were previously used to

store data tracks.

1From stop, press the [ERASE] button.

Erase Standby mode is engaged, “ERASE xxxx” ﬂashes on the display (“xxxx” being the

selected Erase function), and the REC indicators ﬂash.

If the next step is not performed within four seconds, Erase Standby mode is cancelled.

2Use the [PREV] and [NEXT] button to select an Erasure function.

The selected mode appears on the display.

You can cancel Erase Standby mode by pressing the [STOP] button.

3Press the [PLAY] button to start erasure.

Erasure starts, “ERASING” appears on the display, the REC indicators light up contin-

uously, and the PLAY indicators ﬂash.

The time remaining to complete the erasure process counts down on the display in

minutes and seconds. No other CDR1000 functions can be used while erasure is in

progress. With discs that support recording at 4x normal speed, erasure takes place at

4x normal speed.

When the erasure process is ﬁnished, the REC and PLAY indicators go out and “ERAS-

ING” disappears from the display.

If an error message appears when using the Initialize erase function, run the function

again.

Auto Unﬁnalize allows you to record additional tracks to ﬁnalized CD-RW discs. When

a ﬁnalized CD-RW disc is loaded, and a new track is selected for recording in the nor-

mal way, the disc is unﬁnalized automatically and recording carried out as normal. It

takes about one minute to unﬁnalize a disc, during which time “WAIT” appears on the

display.

Functions Description

TRACK Erases the last recorded track

DISC Erases all tracks on the disc quickly

INITIALIZE Erases all tracks and initializes the entire disc

Contents

Main E PROFESSIONAL AUDIO CD RECORDER Keep This Manual For Future Reference. Owners Manual PROFESSIONAL AUDIO CD RECORDER POWER FCC INFORMATION (U.S.A.) IMPORTANT 1 2 3 JUISTE GEBRUIK EN BEHANDELING V AN BA TTERIJEN i Important Information Warnings Read the Following Before Operating the CDR1000 ii Handling Discs Cautions Note Contents 1 Introduction Transportation Pad Installation About this Manual CDR1000 Features Page Operating Notes Page 2 Touring the CDR1000 I H G Page 8 Display 88 88 88 88 CDR1000 K L Function Buttons A B C 1 2 3 4 10 D E F G Rear Panel A B C D 12 Remote Controller 14 Block Diagram The Basics 15 3 The Basics Hookup Examples Analog Coaxial AES/EBU Connecting the Power Cord Turning On the Power Using the Transportation Pad Installing the Transportation Pad 18 Loading & Unloading Discs Disc Type & Status Using the Remote Controller Installing the Remote Controllers Batteries Setting the Time Display 20 Monitoring Metering & Peak Hold Setting the Meter Response Rate 4 Playback Playing Discs Pausing Playback Stopping Playback 22 Playback Operation Table Selecting Tracks Selecting Tracks Directly Selecting Indexes 24 Searching Using Repeat Playback One-track Repeat Playback All-track Repeat Playback A-B Repeat Playback 5 Recording Preparing to Record Selecting the Input Source 26 Setting the Sampling Rate Converter Setting the Input Delay 28 Setting the UV22 Setting the Copy Bit Recording 30 Recording Operation Table 31 Recording Operation Table 32 Incrementing Track Numbers Manually Incrementing Index Numbers Manually 34 Using Auto Rec Start & Track Increment Inserting a Two-second Mute Inserting a Mute at the Beginning of a Track 36 Inserting a Mute at the End of a Track Applying a Fade In 38 Applying a Fade Out Sync Recording from CD, MD, or DAT 40 One-track Sync Recording Page 42 All-track Sync Recording Page 44 Finalizing Discs Erasing Discs (CD-RW only) 46 6 Other Functions Selecting the AES/EBU OUT Playback Clock Selecting the AES/EBU OUT Playback Clock 47 Note: If the message OUT OF RANGE appears while monitoring, stop and reset the sampling rate. Wordclock out WORD CLOCK IN (wordclock slave, source: WORD) 00 00 00 00 mYGDAI YGDAI Using Digital Output Thru Using Digital Output Thru 49 CDR1000 (source machine) PARALLEL AES/EBU OUT PARALLEL AES/EBU IN AES/EBU OUT AES/EBU IN Using a Footswitch Disabling the Remote Controller Using the Parallel Port Parallel Port Pin Conguration 52 Troubleshooting Troubleshooting 53 54 Appendix Error Messages If the CDR1000 displays an error message, follow the instructions below. Specifications 55 Specications 56 Analog Input Analog Output Digital Audio Input Digital Audio Output Dimensions 58 Glossary Index A B C D O P R S T