Yamaha CDR1000 Recording

Recording 29

CDR1000—Owner’s Manual

Recording

This section explains how to record.

The following illustration shows the procedure for recording.

1Prepare for recording as explained on page 25.

2From stop, press the [REC] button to engage Record Standby mode.

Record Standby mode is engaged, the PAUSE indicator lights up, and the REC indica-

tors ﬂash. If the loaded disc is a blank disc, track 1 is selected for recording. If it’s a par-

tially recorded disc, the next available track is selected.

The time counter can be set to display the elapsed record time, remaining record time,

or total record time. See “Setting the Time Display” on page 19 for more information.

In Record Standby mode, the selected input source can be monitored via the ANALOG

OUT, AES/EBU OUT, COAXIAL OUT, or PHONES, and metered on the CDR1000

level meters.

You can cancel Record Standby mode by pressing the [STOP] button.

3If recording via the ANALOG IN, use the REC LEVEL control to set the recording

level in conjunction with the level meters.

The recording level can be set independently for the left and right channels. The record-

ing level for the AES/EBU IN and COAXIAL IN is determined by the source and cannot

be set on the CDR1000.

A two-second mute can be inserted at the beginning of a track by using the Rec Mute

function. See “Inserting a Two-second Mute” on page 35 for more information.

4Press the [PLAY] or [PAUSE] button to start recording.

Recording starts, the PAUSE indicator goes out, the REC indicators light up continu-

ously, the PLAY indicators light up, and the time counter starts counting. If the Fade In

function is set, fade in processing is performed. See “Applying a Fade In” on page 37 for

more information.

Recording can also be started by using an optional footswitch. See “Using a Footswitch”

on page 50 for more information.

Record Standby modeRecording starts

Tn=1 Tn=2

PAUSE

PLAY

Record

Standby

mode

REC STOP

(Recording can also be

started by pressing the

[PAUSE] button or

footswitch)

Recording stops

Press the [PAUSE] button again

12

Contents

Main E PROFESSIONAL AUDIO CD RECORDER Keep This Manual For Future Reference. Owners Manual PROFESSIONAL AUDIO CD RECORDER POWER FCC INFORMATION (U.S.A.) IMPORTANT 1 2 3 JUISTE GEBRUIK EN BEHANDELING V AN BA TTERIJEN i Important Information Warnings Read the Following Before Operating the CDR1000 ii Handling Discs Cautions Note Contents 1 Introduction Transportation Pad Installation About this Manual CDR1000 Features Page Operating Notes Page 2 Touring the CDR1000 I H G Page 8 Display 88 88 88 88 CDR1000 K L Function Buttons A B C 1 2 3 4 10 D E F G Rear Panel A B C D 12 Remote Controller 14 Block Diagram The Basics 15 3 The Basics Hookup Examples Analog Coaxial AES/EBU Connecting the Power Cord Turning On the Power Using the Transportation Pad Installing the Transportation Pad 18 Loading & Unloading Discs Disc Type & Status Using the Remote Controller Installing the Remote Controllers Batteries Setting the Time Display 20 Monitoring Metering & Peak Hold Setting the Meter Response Rate 4 Playback Playing Discs Pausing Playback Stopping Playback 22 Playback Operation Table Selecting Tracks Selecting Tracks Directly Selecting Indexes 24 Searching Using Repeat Playback One-track Repeat Playback All-track Repeat Playback A-B Repeat Playback 5 Recording Preparing to Record Selecting the Input Source 26 Setting the Sampling Rate Converter Setting the Input Delay 28 Setting the UV22 Setting the Copy Bit Recording 30 Recording Operation Table 31 Recording Operation Table 32 Incrementing Track Numbers Manually Incrementing Index Numbers Manually 34 Using Auto Rec Start & Track Increment Inserting a Two-second Mute Inserting a Mute at the Beginning of a Track 36 Inserting a Mute at the End of a Track Applying a Fade In 38 Applying a Fade Out Sync Recording from CD, MD, or DAT 40 One-track Sync Recording Page 42 All-track Sync Recording Page 44 Finalizing Discs Erasing Discs (CD-RW only) 46 6 Other Functions Selecting the AES/EBU OUT Playback Clock Selecting the AES/EBU OUT Playback Clock 47 Note: If the message OUT OF RANGE appears while monitoring, stop and reset the sampling rate. Wordclock out WORD CLOCK IN (wordclock slave, source: WORD) 00 00 00 00 mYGDAI YGDAI Using Digital Output Thru Using Digital Output Thru 49 CDR1000 (source machine) PARALLEL AES/EBU OUT PARALLEL AES/EBU IN AES/EBU OUT AES/EBU IN Using a Footswitch Disabling the Remote Controller Using the Parallel Port Parallel Port Pin Conguration 52 Troubleshooting Troubleshooting 53 54 Appendix Error Messages If the CDR1000 displays an error message, follow the instructions below. Specifications 55 Specications 56 Analog Input Analog Output Digital Audio Input Digital Audio Output Dimensions 58 Glossary Index A B C D O P R S T