Yamaha CDR1000 5 Recording

Recording 25

CDR1000—Owner’s Manual

5 Recording

Preparing to Record

The CDR1000 can record onto CD-R and CD-RW discs.

1Load the disc to be used for recording.

See “Loading & Unloading Discs” on page 18 for more information.

2Select the input source.

See “Selecting the Input Source” below for more information.

3If recording via the AES/EBU IN or COAXIAL IN, set the sampling rate con-

verter as necessary.

See “Setting the Sampling Rate Converter” on page 26 for more information.

4Set the Copy Bit as required.

See “Setting the Copy Bit” on page 28 for more information.

5Set the UV22 function as required.

See “Setting the UV22” on page 28 for more information.

6Set the Delay function as required.

See “Setting the Input Delay” on page 27 for more information.

7Proceed to Recording on page 29.

Selecting the Input Source

The following input sources can be selected for recording: ANALOG IN, AES/EBU IN,

or COAXIAL IN. The selected source is indicated on the display.

1Use the [INPUT SELECT] button to select an input source.

When a digital input source is selected, the LOCK indicator lights up, indicating that

the CDR1000 is locked to the incoming signal. If the CDR1000 cannot lock to the

selected digital input source, the LOCK indicator ﬂashes. If this unlocked condition

continues for more than ﬁve seconds while recording, recording stops. If this happens,

make sure that the source device is turned on and connected to the CDR1000 correctly,

or select another input source. Recording via the AES/EBU IN or COAXIAL IN is not

possible while the LOCK indicator is ﬂashing.

Setting Description

ANALOG ANALOG IN (analog)

AES/EBU AES/EBU IN (AES/EBU digital)

COAX COAXIAL IN (S/PDIF digital)

Contents

Main E PROFESSIONAL AUDIO CD RECORDER Keep This Manual For Future Reference. Owners Manual PROFESSIONAL AUDIO CD RECORDER POWER FCC INFORMATION (U.S.A.) IMPORTANT 1 2 3 JUISTE GEBRUIK EN BEHANDELING V AN BA TTERIJEN i Important Information Warnings Read the Following Before Operating the CDR1000 ii Handling Discs Cautions Note Contents 1 Introduction Transportation Pad Installation About this Manual CDR1000 Features Page Operating Notes Page 2 Touring the CDR1000 I H G Page 8 Display 88 88 88 88 CDR1000 K L Function Buttons A B C 1 2 3 4 10 D E F G Rear Panel A B C D 12 Remote Controller 14 Block Diagram The Basics 15 3 The Basics Hookup Examples Analog Coaxial AES/EBU Connecting the Power Cord Turning On the Power Using the Transportation Pad Installing the Transportation Pad 18 Loading & Unloading Discs Disc Type & Status Using the Remote Controller Installing the Remote Controllers Batteries Setting the Time Display 20 Monitoring Metering & Peak Hold Setting the Meter Response Rate 4 Playback Playing Discs Pausing Playback Stopping Playback 22 Playback Operation Table Selecting Tracks Selecting Tracks Directly Selecting Indexes 24 Searching Using Repeat Playback One-track Repeat Playback All-track Repeat Playback A-B Repeat Playback 5 Recording Preparing to Record Selecting the Input Source 26 Setting the Sampling Rate Converter Setting the Input Delay 28 Setting the UV22 Setting the Copy Bit Recording 30 Recording Operation Table 31 Recording Operation Table 32 Incrementing Track Numbers Manually Incrementing Index Numbers Manually 34 Using Auto Rec Start & Track Increment Inserting a Two-second Mute Inserting a Mute at the Beginning of a Track 36 Inserting a Mute at the End of a Track Applying a Fade In 38 Applying a Fade Out Sync Recording from CD, MD, or DAT 40 One-track Sync Recording Page 42 All-track Sync Recording Page 44 Finalizing Discs Erasing Discs (CD-RW only) 46 6 Other Functions Selecting the AES/EBU OUT Playback Clock Selecting the AES/EBU OUT Playback Clock 47 Note: If the message OUT OF RANGE appears while monitoring, stop and reset the sampling rate. Wordclock out WORD CLOCK IN (wordclock slave, source: WORD) 00 00 00 00 mYGDAI YGDAI Using Digital Output Thru Using Digital Output Thru 49 CDR1000 (source machine) PARALLEL AES/EBU OUT PARALLEL AES/EBU IN AES/EBU OUT AES/EBU IN Using a Footswitch Disabling the Remote Controller Using the Parallel Port Parallel Port Pin Conguration 52 Troubleshooting Troubleshooting 53 54 Appendix Error Messages If the CDR1000 displays an error message, follow the instructions below. Specifications 55 Specications 56 Analog Input Analog Output Digital Audio Input Digital Audio Output Dimensions 58 Glossary Index A B C D O P R S T