Connecting the antennas | Yamaha DVX-S100 manual

CONNECTIONS

Connecting the antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength.

Connect each antenna correctly to the designated terminals.

■Connecting indoor FM antenna

Connect the included indoor FM antenna to the FM ANT terminal.

■Connecting the AM loop antenna

1Set up the AM loop antenna, then connect it.

Indoor FM antenna	AM loop antenna
(included)	(included)

FM ANT	GND – AM ANT
75ΩUNBAL.

Ground (GND terminal) For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

2Press and hold the tab to insert the AM loop antenna lead wires into the AM ANT and GND terminals.

Bare wire

Tab

3Release the tab. (The tab will return to its original position when you release your finger.)

Once connected, pull the wires gently to check that they are connected securely.

4Orient the AM loop antenna for the best reception.

y

•A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas.

Notes

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

16

Image 20

Yamaha DVX-S100 owner manual Connecting the antennas, Connecting indoor FM antenna, Connecting the AM loop antenna

Contents

DVX-S100 Important Safety Instructions Explanation of Graphical Symbols FCC Information for US customers only Example of Antenna Grounding We Want You Listening For a Lifetime For Canadian Customers Contents Features About this manual Checking the Accessories Installing Batteries in the Remote ControlDVR-S100 NX-SW100 NX-S100S x4, NX-S100C, SW-S100 STANDBY/ON Controls and FunctionsFront panel Introduction Input H/G Remote control AMP mode Code SETLevel Test Approximately 6 m 20 feet Using the remote controlHandling the remote control Front panel display left Front panel display right Before connecting components Adjusting speaker output levels P.20After connecting components Preparation Steps Preparation Speaker SetupSpeaker placement Installing the speakers Placing the center speakerMounting the front and rear speakers Placing the front and rear speakers Hang the holes on the protruding screws Connections ComponentsTypes of video jacks Types of audio jacks Connection example For Audio componentFor Video Component For A/V component Connecting the antennas Connecting indoor FM antennaConnecting the AM loop antenna Set up the AM loop antenna, then connect it Connecting the speakers RED WhiteGreen Gray Blue Using commercially available speakers and speaker cables Exchanging the speaker cables Connecting to an external Amplifier Connecting the AC power cordTurning on the power Memory back-up Adjusting Speaker Output Levels Using the test toneLeft Right Center Subwoofer SUR AMP Basic Playback Basic operationsEnhancing the bass tones To mute the sound Input modes and indications When you have finished using this unitSetting the sleep timer Feature of DSP programs UsingSelecting a sound field program Basic Functions Program Features CINEMA-DSP for cinema sourcesTV Sports Mono Movie Means the Matrix 6.1 decoder is on Using Basic FunctionsTable of Program Names for Each Input Format Selecting PRO Logic Playing Dolby Digital Surround EX or DTS ES softwareVirtual Cinema DSP While playing a 2-channel source Press AMP Press q/DTS Displaying the information about input signal Normal Stereo Reproduction Recording Special considerations when recording DTS softwareTimer playback/recording Disc Information Types of disc that this unit can PlayPlaying a Disc This manual, the type of discs are indicated as below MP3 playback Structure of the disc exampleStarting play from a selected chapter Repeat play Remote Control DVD Mode SetupPlay Mode Subtitle Playing a Disc Basic operationTo stop playback After operation Skip To select a specific trackSearch Pause ON-SCREEN Menu Operating menu barTo turn the screen off To change the menu bar position Language Signal type/dataIcons for disc menu Play mode menu Icons for player menuDisplay menu Audio menu Digital picture mode Transfer ModeTo change the user mode Shuttle screen Using Multiple Functions Using a disc’s menuEnhancing video quality U.S.A Canada models only Video CD’s playback control VCD Adjusting the screen position when using progressive output Save the adjusted positionTo play a track on a specific group A. and Canada models Enhancing audio quality Disc To play a bonus groupTo change pages Press a to stop play Press Group while pressing Shift Audio tracks SubtitlesAngles To turn the icon off Press a to stop play Press Play Mode while pressing Shift Programmed playCase of DVD-Audio Press a to stop play To cancel the programmed tracks To exit programming modeTo change or add to the program during programmed play To move up and down the pages on the program screen To cancel random mode Random play DVD-AudioTo play from the marked point To clear a bookmark Program repeat Random-sequence repeatDVD-Video DVD-Audio/Video-CD/CD Repeat A-BDVD-A DVD-V VCD CD To cancel A-B repeatPress A-B while pressing Shift Setup Menu Operating the setup menuTo get out from the setup menu mode To go back to the previous screen DVD-A DVD-V Summary of settingsMenu groups Items Options Mpeg DVD-A DVD-V VCD Language selection and language code list Language code listOthers DVD-Video Mode Demo To change settings Level 7 to If you have forgotten your passwordSetting method Level Ratings DVD-V Speaker settings DVD-A DVD-V Output mode To exit the speaker setting mode Difference SettingDifference Setting Speaker balance Tuning Automatic and manual tuningAutomatic tuning Manual tuning Presetting stations Automatically presetting stations for FM stationsManually presetting stations Tuning Tuning in to a preset station Press PRESET/BAND againRepeat steps 1 to 5 to store other stations Seconds Setting the manufacturer code Remote Control FeaturesYou can release Code SET after entering the code MD/CD-R Table of control buttons CD/MD recorder0, ≥10 CH + Adjusting the items on the SET AdjustmentsSET Menu List of SET Menu items Settings 1A Center center speaker mode1B Front front speaker mode 1C Rear LR rear speaker mode 1D Bass LFE/bass out mode 1E F. Level front level modeSwfr Both SP DLY Time speaker delay Range dynamic rangeR Balance balance Front left and right speakers Control Input Mode initial input SP/PRE OUT output source SettingsOptical Input jack Coaxial Input jack Adjusting the Level of the Effect Speakers Press j / i to adjust the speaker output levelFor 5ch Stereo Level Adjusting the delay time Following table shows factory-set delay time Adjusting the parameter settings for PRO Logic II Music Changing parameter settingsDimension PRO Logic II Music parameter descriptions Troubleshooting Problem Cause Remedy ReferGeneral Appendix Volume level No sound fromCenter speaker Rear speakers Problem Cause Disc playback Remedy Refer On the unit’s display This unit does not Remote control Tuner Glossary Cinema DSP Interlace and progressive output Video signal Silent Cinema Specifications List of MANUFACTURER’S Codes VCR CDR Kenwood Pioneer Sharp V883340-1