Troubleshooting

 

 

 

 

Problem

Cause

Remedy

See

page

 

 

 

The sound suddenly

The protection circuitry has been activated

Check that the impedance setting is correct.

23

goes off.

because of a short circuit, etc.

 

 

Check that the speaker wires are not touching each

 

 

 

 

other and then turn this unit back on.

 

 

 

 

 

 

The sleep timer has turned off this unit.

Turn on this unit, and play the source again.

 

 

 

 

 

The sound is muted.

Press JMUTE or NVOLUME +/– to resume audio

37

 

 

output.

 

 

 

 

 

Sound is heard from

Incorrect cable connections.

Connect the cables properly. If the problem persists,

11-19

the speaker on one

 

the cables may be defective.

 

side only.

 

 

 

Incorrect settings in “SP LEVEL”.

Adjust the “SP LEVEL” settings.

43

 

 

 

 

 

Only the center

When playing a monaural source with a

This is not malfunction.

speaker outputs

CINEMA DSP program, the source signal

 

 

substantial sound.

is directed to the center channel, and the

 

 

 

front and surround speakers output effect

 

 

 

sounds.

 

 

 

 

 

 

No sound is heard

“CENTER SP” in “SPEAKER SET” is set

Set “CENTER SP” to “SML” or “LRG”.

65

from the center

to “NONE”.

 

 

speaker.

 

 

 

One of the HiFi DSP programs (except for

Try another sound field program.

40

 

 

7ch Stereo) has been selected.

 

 

 

 

 

 

No sound is heard

“SUR. L/R SP” in “SPEAKER SET” is

Set “SUR. L/R SP” to “SML” or “LRG”.

66

from the surround

set to “NONE”.

 

 

speakers.

 

 

 

This unit is in the “STRAIGHT” mode

Press PSTRAIGHT so that “STRAIGHT”

41

 

 

and a monaural source is being played

disappears from the front panel display.

 

 

back.

 

 

 

 

 

 

No sound is heard

“SUR. L/R SP” in “SPEAKER SET” is

Set “SUR. L/R SP” and “SUR. B L/R SP” to a setting

66

from the surround

set to “NONE” and “SUR.B L/R SP” is

other than “NONE”.

 

back speakers.

automatically set to “NONE”.

 

 

 

 

 

 

 

“SUR.B L/R SP” in “SPEAKER SET” is

Set “SUR.B L/R SP” to a setting other than “NONE”.

66

 

set to “NONE”.

 

 

 

 

 

 

No sound from the

“FRONT B” in “SPEAKER SET” is set to

Set “FRONT B” to “FRONT”.

65

center, surround or

“ZONE B”.

 

 

surround back

 

 

 

speakers when the

 

 

 

FRONT B speakers

 

 

 

are activated.

 

 

 

 

 

 

 

No sound is heard

“LFE/BASS OUT” in “SPEAKER SET”

Set “LFE/BASS OUT” to “SWFR” or “BOTH”.

66

from the subwoofer.

is set to “FRNT” when a Dolby Digital or

 

 

 

DTS signal is being played.

 

 

 

 

 

 

 

“LFE/BASS OUT” in “SPEAKER SET”

Set “LFE/BASS OUT” to “SWFR” or “BOTH”.

66

 

is set to “SWFR” or “FRNT” when a 2-

 

 

 

channel source is being played.

 

 

 

 

 

 

 

The source does not contain low-

This is not malfunction.

 

frequency bass signals.

 

 

 

 

 

 

INFORMATION

ADDITIONAL

 

 

English

85 En

Page 89
Image 89
Yamaha RX-V563 owner manual 85 En, Problem Cause Remedy