Troubleshooting

 

 

 

 

Problem

Cause

Remedy

See

page

 

 

 

 

 

 

 

No picture.

An appropriate video input is not selected

Select an appropriate video input on the monitor.

—

 

on the monitor.

 

 

 

 

 

 

 

The composite output terminals are used

If your monitor does not support the HDMI

14

 

to output a component video signal, or the

connection, connect it to the COMPONENT OUT

 

 

COMPONENT VIDEO jacks are used to

jacks or the composite output terminals and select an

 

 

output a composite video signal.

appropriate video input on the monitor.

 

 

 

 

 

 

This unit outputs the video signals are not

Displays the advanced setup menu and select

45

 

supported on the video monitor connected

“VIDEO” in “INIT” to reset the video parameters.

 

 

to the HDMI OUT jack.

 

 

 

Displays the advanced setup menu and set

45

 

 

“MON.CHK” to “YES.”

Non-standard video signals are input.

Connect the monitor to this unit via the

14

COMPONENT OUT jacks or the composite output terminals.

The sound suddenly

The protection circuitry has been activated

goes off.

because of a short circuit, etc.

Check that the speaker impedance setting is correct.

45

 

 

Check that the speaker wires are not touching each

—

other and then turn this unit back on.

 

 

The sleep timer has turned off this unit.

Turn on this unit, and play the source again.

—

 

 

 

 

Sound is heard from

The playback component or speakers are

Connect the cables properly. If the problem persists,

11

the speaker on one

not connected properly.

the cables may be defective.

 

side only.

 

 

 

The speaker level settings are incorrect.

Adjust “B)Level” settings.

41

 

 

 

 

 

Only the center

When a monaural source sound field

Try another sound field program.

24

speaker outputs

program is applied, sound of all channels

 

 

substantial sound.

are output from the center speaker for

 

 

 

some surround decoders.

 

 

 

 

 

 

No sound is output

Output from that speaker is disabled.

Check the Speaker indicators on the front panel

6, 21, 24,

from a specific

 

display. If the corresponding indicator is turned off,

40

speaker.

 

try the following.

 

 

 

1) Change the input source to another one.

 

 

 

2) With the selected sound field program, sound is not

 

 

 

output from that speaker. Select another sound field

 

 

 

program.

 

 

 

3) “None” may have been selected for that speaker on

 

 

 

this unit. Display Speaker Setup in the Setup menu

 

 

 

and enables output of that speaker.

 

 

 

 

 

 

The volume of that speaker is set to

Display Speaker Setup in the Setup menu and adjust

41

 

minimum in Speaker Setup in the Setup

the volume (Manual Setup→B)Level).

 

menu.

APPENDIX

 

This unit or speaker is malfunction.

Check the Speaker indicators on the front panel

6, 10

 

 

 

 

display. If the corresponding indicator lights up,

 

 

 

 

 

connect another speaker and check if sound is output.

 

 

 

 

 

If sound is not output, this unit may be malfunction.

 

 

 

 

 

 

 

 

 

No sound is heard

This unit is in the “STRAIGHT” mode

Press LSTRAIGHT or the jSTRAIGHT on the

27

 

 

from the surround

and a monaural source is being played

remote control to turn off the “STRAIGHT” mode.

 

 

 

speakers.

back.

 

 

 

 

 

 

 

 

 

 

 

Sound may not be output from certain

Try another sound field program.

24

 

 

 

channels depending on input sources or

 

 

 

 

 

 

 

 

 

 

sound field programs.

 

 

 

English

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

47 En