Yamaha yamaha digiatal mixing console Using the Oscillator

Using the Oscillator 45

01V96i—Owner’s Manual

Tutor ial

Using the Oscillator

The 01V96i features an Oscillator you can use for

sound checks. Follow the steps below to use the Oscil-

lator:

1. Press the DISPLAY ACCESS [UTILITY] but-

ton repeatedly until the Utility | Oscillator

page appears.

This page contains the following parameters:

1OSCILLATOR ON

This parameter button turns the Oscillator on or

off.

2WAVEFORM

These parameter buttons select the Oscillator wave-

forms.

3LEVEL section

The parameter control in this section sets the Oscil-

lator output level.

4ASSIGN section

The buttons in this section select the Oscillator out-

put.

2. Move the cursor to the button for the

Oscillator output channel in the ASSIGN

section, then press [ENTER] (you can

select multiple channels).

3. Move the cursor to one of the WAVE-

FORM parameter buttons, then press

[ENTER].

You can select the following waveforms:

•SINE 100Hz........100 Hz sinewave

•SINE 1kHz...........1 kHz sinewave

•SINE 10kHz ........10 kHz sinewave

•PINK NOISE......Pink noise

•BURST NOISE ...Burst noise (200 msec pink noise

pulses at four second intervals)

4. Move the cursor to the parameter con-

trol in the LEVEL section, then rotate the

Parameter wheel to set the Oscillator

level to minimum.

5. Move the cursor to the OSCILLATOR

ON/OFF button, then press the [ENTER]

or [INC]/[DEC] buttons to turn on the

Oscillator.

The Oscillator signal is now routed to the channels

selected in the ASSIGN section.

6. Move the cursor to the parameter con-

trol in the LEVEL section, then rotate the

Parameter wheel to raise the Oscillator

level.

You can view the current Oscillator level on the

LEVEL meter.

1 3

2 4

Note: Sinewave and pink noise create unusually high

sound pressure. Oscillator levels that are too high can

damage the speakers. When you use the Oscillator, be

sure to set the level to minimum, then raise the level

gradually.

Contents

Main 2 Contents Explanation of Graphical Symbols IMPORTANT SAFETY INSTRUCTIONS CAUTION WARNING 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! 2. IMPORTANT: FCC INFORMATION (U.S.A.) IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord ADVARSEL! VARNING VAROITUS PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNIN G CAUTION Notice may cause the panel to be discolored or disfigured. Information Connections Maintenance Welcome Package Contents About the included discs About the included DAW software About the utility software Firmware updates About this Owners Manual Owners manual (this document) Reference manual (PDF format / on the included CD-ROM) Conventions Used in this Manual Control Surface & Rear Panel 32313029282726252423222120191817 STEREO 13 14 15 16 78 9 10 11 12 123456 10 AD Input Section 1 2 3 Monitor Out & Headphones Section 1 2 3 4 12 ST IN Section 90 A B 1 2 LAYER Section 1 2 3 Display Section 14 SELECTED CHANNEL Section 1 2 3 4 5 6 Data Entry Section 1 1 2 2 3 Rear Panel PHANTOM +48V 1 2 3 AD Output Section 1 Digital I/O Section 1 2 3 4 Installing an Optional Card 1. is turned off. 2. the slot cover, as shown below. Operating Basics About the Display CBA 1 2 Selecting Display Pages 1. top panel to select the desired page group. 2. rently-displayed tabs by pressing the [F1][F4] buttons. Selecting Layers Selecting Channels 1. LAYER button to select a layer that includes the desired channel (see page 21). 2. select the desired channel. Metering 1. 1 2 2. 4. the cursor to the PEAK HOLD button, then press [ENTER]. Connections and Setup 25 Connections OMNI OUT connector Connections and Setup This chapter explains how to connect and set up your 01V96i. Connections Configuring an analog 1624-channel mixing system Synthesizer Synthesizer Configuring a recording system that uses a DAW (Digital Audio Workstation) TO HOST USB port Monitoring system Synthesizer 32313029282726252423222120191817 STEREO Wordclock Connections and Settings External device About Wordclock Wordclock Connections WC OUT (BNC) 28 Specifying the Wordclock Source 1. button repeatedly until the DIO/Setup | Word Clock page appears. sor to a source, then press [ENTER]. Input and Output Patching Patching Input Channels ton repeatedly until the following page appears. Patching Omni Outs ton repeatedly until the following page appears. 30 Patching output signals to USB OUT 1. 2. Tut or ia l Input and Output Patching Input Patching 2. Output Patching Setting the Input Levels 1. 2. 3. 4. Pairing Channels 1. 2. button for one of the paired channels, and press the [SEL] button for the other channel. Setting the Routing 1. 1 2 3 2. EQing the Input Signals 2. 3. 4. 5. Using the EQ Library 2. 3. 4. 5. Compressing the Input Signals 2. 3. 4. 5. Using the Internal Effects 2. 3. 4. 5. Recording to DAW Software via the USB Port Recording Bus Outs 18 1. 2. 40 3. 4. 5. 6. 7. Adjusting the Monitor Levels from the DAW 1. 2. 3. 4. Using Scene Memories 1. 2. 3. 4. Changing the Channel Names Changing the Input Channel Names ton repeatedly until the Patch| In Name page appears. 2. 3. Creating a Custom Layer by Combining Channels (User Assignable Layer) 1. 2. 3. 4. Using the Oscillator 1. 1 2 3 Using the User Defined Keys 1. 1 2 3 Using Operation Lock 31 2 1 2 3 Initializing 1. 2. 3. 4. Troubleshooting 50 Error messages Error messages 52 Error messages 54 Contents of the Reference Manual Specifications General Spec Page General Spec 57 Page General Spec 59 EQ Parameters Gate Parameters Comp Parameters Libraries Analog Input Spec 61 Analog Input Spec Analog Output Specs Digital Input Spec Digital Output Spec I/O SLOT Spec 63 I/O SLOT Spec The I/O SLOT accepts a mini YGDAI card. The SLOT has a serial interface. MIDI/USB/WORD CLOCK I/O Spec Dimensions Options Rack Mounting the 01V96i Using RK1 Rack Mount Kit 66 Index Symbols Numerics A B Q R S T U Page 01V96i Level Diagram Analog Digital Analog DigitalAnalog NORTH AMERICA CENTRAL & SOUTH AMERICA EUROPE AFRICA MIDDLE EAST ASIA