Yamaha yamaha digiatal mixing console Installing an Optional Card

18 Control Surface & Rear Panel

01V96i—Owner’s Manual

SLOT Section

1SLOT

Optional mini-YGDAI (Yamaha General Digital

Audio Interface) I/O cards can be installed in this

slot. You can install AD/DA cards or digital I/O

cards supporting a variety of digital formats includ-

ing AES/EBU, ADAT, and Tascam.

Input signals from an I/O card can be patched to

any desired input channel or insert-in (see page29).

The output signal of any desired bus or the direct

signal of an i nput channe l can be p atched to an out-

put of an I/O card (see page30).

Power Section

1POWER ON/OFF

switch

This switch turns the

power to the 01V96i on

or off.

2AC IN connector

This connector enables you to connect the 01V96i

to an AC outlet via the supplied power cord. Be sure

to plug the AC power cord into this connector

before plugging the power cord into an AC outlet.

Caution

Even when the POWER ON/OFF switch is in the

off position, a small amount of ele ctricity is still

flowing to the unit. When you are not using the

01V96i for a long time, make sure to unplug the

AC power cord from the AC outlet .

Installing an Optional Card

Visit the following Yamaha Pro Audio web site to

ensure that the card you are installing is supported by

the 01V96i.

http://www.yamahapro audio.com/

Follow the steps below to install an optional

mini-YGDAI card.

1. Make sure that the power to the 01V96i

is turned off.

2. Undo the two fixing screws and remove

the slot cover, as shown below.

Keep the cover and fixing screws in a safe place for

future use.

3. Insert the card between the guide rails

and slide it all the way into the slot, as shown below.

You may have to push firmly to fully insert the card

into the internal connector.

4. Secure the card using the attached

thumbscrews.

Tighten the screws firmly to sec ure the card. Other-

wise, the card may not be grounded correctly.

Note:

• See page 63 for information on the

mini-YGDAI I/O cards that can be currently

used.

• For the latest information about I/O cards,

refer to the Yamaha Pro Audio website.

http://www.yamahaproaudio.com/

Note: To prevent loud clicks and thumps in your speak-

ers, turn on your audio equipment in the following

order (reverse this order when turning the equipment

off)—sound sources, multitrack and master recorders,

01V96i, monitoring power amplifiers.

1

21

Contents

Main 2 Contents Explanation of Graphical Symbols IMPORTANT SAFETY INSTRUCTIONS CAUTION WARNING 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! 2. IMPORTANT: FCC INFORMATION (U.S.A.) IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord ADVARSEL! VARNING VAROITUS PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNIN G CAUTION Notice may cause the panel to be discolored or disfigured. Information Connections Maintenance Welcome Package Contents About the included discs About the included DAW software About the utility software Firmware updates About this Owners Manual Owners manual (this document) Reference manual (PDF format / on the included CD-ROM) Conventions Used in this Manual Control Surface & Rear Panel 32313029282726252423222120191817 STEREO 13 14 15 16 78 9 10 11 12 123456 10 AD Input Section 1 2 3 Monitor Out & Headphones Section 1 2 3 4 12 ST IN Section 90 A B 1 2 LAYER Section 1 2 3 Display Section 14 SELECTED CHANNEL Section 1 2 3 4 5 6 Data Entry Section 1 1 2 2 3 Rear Panel PHANTOM +48V 1 2 3 AD Output Section 1 Digital I/O Section 1 2 3 4 Installing an Optional Card 1. is turned off. 2. the slot cover, as shown below. Operating Basics About the Display CBA 1 2 Selecting Display Pages 1. top panel to select the desired page group. 2. rently-displayed tabs by pressing the [F1][F4] buttons. Selecting Layers Selecting Channels 1. LAYER button to select a layer that includes the desired channel (see page 21). 2. select the desired channel. Metering 1. 1 2 2. 4. the cursor to the PEAK HOLD button, then press [ENTER]. Connections and Setup 25 Connections OMNI OUT connector Connections and Setup This chapter explains how to connect and set up your 01V96i. Connections Configuring an analog 1624-channel mixing system Synthesizer Synthesizer Configuring a recording system that uses a DAW (Digital Audio Workstation) TO HOST USB port Monitoring system Synthesizer 32313029282726252423222120191817 STEREO Wordclock Connections and Settings External device About Wordclock Wordclock Connections WC OUT (BNC) 28 Specifying the Wordclock Source 1. button repeatedly until the DIO/Setup | Word Clock page appears. sor to a source, then press [ENTER]. Input and Output Patching Patching Input Channels ton repeatedly until the following page appears. Patching Omni Outs ton repeatedly until the following page appears. 30 Patching output signals to USB OUT 1. 2. Tut or ia l Input and Output Patching Input Patching 2. Output Patching Setting the Input Levels 1. 2. 3. 4. Pairing Channels 1. 2. button for one of the paired channels, and press the [SEL] button for the other channel. Setting the Routing 1. 1 2 3 2. EQing the Input Signals 2. 3. 4. 5. Using the EQ Library 2. 3. 4. 5. Compressing the Input Signals 2. 3. 4. 5. Using the Internal Effects 2. 3. 4. 5. Recording to DAW Software via the USB Port Recording Bus Outs 18 1. 2. 40 3. 4. 5. 6. 7. Adjusting the Monitor Levels from the DAW 1. 2. 3. 4. Using Scene Memories 1. 2. 3. 4. Changing the Channel Names Changing the Input Channel Names ton repeatedly until the Patch| In Name page appears. 2. 3. Creating a Custom Layer by Combining Channels (User Assignable Layer) 1. 2. 3. 4. Using the Oscillator 1. 1 2 3 Using the User Defined Keys 1. 1 2 3 Using Operation Lock 31 2 1 2 3 Initializing 1. 2. 3. 4. Troubleshooting 50 Error messages Error messages 52 Error messages 54 Contents of the Reference Manual Specifications General Spec Page General Spec 57 Page General Spec 59 EQ Parameters Gate Parameters Comp Parameters Libraries Analog Input Spec 61 Analog Input Spec Analog Output Specs Digital Input Spec Digital Output Spec I/O SLOT Spec 63 I/O SLOT Spec The I/O SLOT accepts a mini YGDAI card. The SLOT has a serial interface. MIDI/USB/WORD CLOCK I/O Spec Dimensions Options Rack Mounting the 01V96i Using RK1 Rack Mount Kit 66 Index Symbols Numerics A B Q R S T U Page 01V96i Level Diagram Analog Digital Analog DigitalAnalog NORTH AMERICA CENTRAL & SOUTH AMERICA EUROPE AFRICA MIDDLE EAST ASIA