Yamaha yamaha digiatal mixing console 50

50 Troubleshooting

01V96i—Owner’s Manual

Signal level is low at a specific

frequency

❍Could the EQ gain be excessively low?

❍Routing a signal through GEQ or an effect will delay it relative to other signals. If

a signal is mixed with the same signal routed differently, a comb filter effect will

decrease the level at specific frequencies.

Can’t control the 01V96i console from

01V96i Editor ❍Refer to the 01V96i Editor installation guide on the website.

The 01V96i console is not recognized

by your DAW software

❍Have you downloaded and installed the Yamaha Steinberg USB Driver?

❍You must connect the 01V96i to the computer and power-on the 01V96i before

you start up your DAW software.

❍Check the driver settings and device settings of your DAW software.

Signals are not recorded on your

DAW software

❍Are the input ports set appropriately on your DAW software?

❍If you’re using Cubase, are the VST connection settings appropriate?

❍Is the signal you want to record being routed to one of USB1–16?

Contents

Main 2 Contents Explanation of Graphical Symbols IMPORTANT SAFETY INSTRUCTIONS CAUTION WARNING 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! 2. IMPORTANT: FCC INFORMATION (U.S.A.) IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord ADVARSEL! VARNING VAROITUS PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNIN G CAUTION Notice may cause the panel to be discolored or disfigured. Information Connections Maintenance Welcome Package Contents About the included discs About the included DAW software About the utility software Firmware updates About this Owners Manual Owners manual (this document) Reference manual (PDF format / on the included CD-ROM) Conventions Used in this Manual Control Surface & Rear Panel 32313029282726252423222120191817 STEREO 13 14 15 16 78 9 10 11 12 123456 10 AD Input Section 1 2 3 Monitor Out & Headphones Section 1 2 3 4 12 ST IN Section 90 A B 1 2 LAYER Section 1 2 3 Display Section 14 SELECTED CHANNEL Section 1 2 3 4 5 6 Data Entry Section 1 1 2 2 3 Rear Panel PHANTOM +48V 1 2 3 AD Output Section 1 Digital I/O Section 1 2 3 4 Installing an Optional Card 1. is turned off. 2. the slot cover, as shown below. Operating Basics About the Display CBA 1 2 Selecting Display Pages 1. top panel to select the desired page group. 2. rently-displayed tabs by pressing the [F1][F4] buttons. Selecting Layers Selecting Channels 1. LAYER button to select a layer that includes the desired channel (see page 21). 2. select the desired channel. Metering 1. 1 2 2. 4. the cursor to the PEAK HOLD button, then press [ENTER]. Connections and Setup 25 Connections OMNI OUT connector Connections and Setup This chapter explains how to connect and set up your 01V96i. Connections Configuring an analog 1624-channel mixing system Synthesizer Synthesizer Configuring a recording system that uses a DAW (Digital Audio Workstation) TO HOST USB port Monitoring system Synthesizer 32313029282726252423222120191817 STEREO Wordclock Connections and Settings External device About Wordclock Wordclock Connections WC OUT (BNC) 28 Specifying the Wordclock Source 1. button repeatedly until the DIO/Setup | Word Clock page appears. sor to a source, then press [ENTER]. Input and Output Patching Patching Input Channels ton repeatedly until the following page appears. Patching Omni Outs ton repeatedly until the following page appears. 30 Patching output signals to USB OUT 1. 2. Tut or ia l Input and Output Patching Input Patching 2. Output Patching Setting the Input Levels 1. 2. 3. 4. Pairing Channels 1. 2. button for one of the paired channels, and press the [SEL] button for the other channel. Setting the Routing 1. 1 2 3 2. EQing the Input Signals 2. 3. 4. 5. Using the EQ Library 2. 3. 4. 5. Compressing the Input Signals 2. 3. 4. 5. Using the Internal Effects 2. 3. 4. 5. Recording to DAW Software via the USB Port Recording Bus Outs 18 1. 2. 40 3. 4. 5. 6. 7. Adjusting the Monitor Levels from the DAW 1. 2. 3. 4. Using Scene Memories 1. 2. 3. 4. Changing the Channel Names Changing the Input Channel Names ton repeatedly until the Patch| In Name page appears. 2. 3. Creating a Custom Layer by Combining Channels (User Assignable Layer) 1. 2. 3. 4. Using the Oscillator 1. 1 2 3 Using the User Defined Keys 1. 1 2 3 Using Operation Lock 31 2 1 2 3 Initializing 1. 2. 3. 4. Troubleshooting 50 Error messages Error messages 52 Error messages 54 Contents of the Reference Manual Specifications General Spec Page General Spec 57 Page General Spec 59 EQ Parameters Gate Parameters Comp Parameters Libraries Analog Input Spec 61 Analog Input Spec Analog Output Specs Digital Input Spec Digital Output Spec I/O SLOT Spec 63 I/O SLOT Spec The I/O SLOT accepts a mini YGDAI card. The SLOT has a serial interface. MIDI/USB/WORD CLOCK I/O Spec Dimensions Options Rack Mounting the 01V96i Using RK1 Rack Mount Kit 66 Index Symbols Numerics A B Q R S T U Page 01V96i Level Diagram Analog Digital Analog DigitalAnalog NORTH AMERICA CENTRAL & SOUTH AMERICA EUROPE AFRICA MIDDLE EAST ASIA