Manuals / Brands / Photography / Photo Scanner / Zebra Technologies / Photography / Photo Scanner

Zebra Technologies radio frequency identification (rfid) - page 72

1 162

Download 162 pages, 1.85 Mb

Troubleshooting

RFID Error Codes and Messages

72

58978L-008 Rev. A RFID Programming Guide 11/14/2008

0408 INVALID WR DATA In EPC 0+, the first two bits determine the tag ID length. If the

first two bits are 0b00, then the tag ID must be 96 bits. Otherwise,

the tag ID is 64 bits.

Make sure that the first two bits have the correct values,

depending on the tag ID length.

0409 INVALID ADDR The RFID reader received a command to write to an invalid

address in the tag data address space. Make sure that the address

specified is within the scope of the tag data address space.

040A TAG ERROR Internal problem with the reader. If the problem persists, contact

Technical Support.

040B DATA TOO LARGE Internal problem with the reader. If the problem persists, contact

Technical Support.

0420 GEN2 PROT OTHER Internal problem with the reader. If the problem persists, contact

Technical Support.

0423 GEN2 BAD PC Internal problem with the reader. If the problem persists, contact

Technical Support.

0424 GEN2 MEM LOCKED Internal problem with the reader. If the problem persists, contact

Technical Support.

042B GEN2 LOW PWR Internal problem with the reader. If the problem persists, contact

Technical Support.

042F GEN2 ERROR Internal problem with the reader. If the problem persists, contact

Technical Support.

0430 GEN2 UNKNWN ERR Internal problem with the reader. If the problem persists, contact

Technical Support.

0500 INVALID FREQ The RFID reader received a command to set the frequency outside

of the supported range. If the problem persists, contact Technical

Support.

0600 TAG ID FAULT The reader received a command to get a certain number of tag IDs

from the tag ID buffer. The reader contains less tag IDs stored in

its tag ID buffer than the number the host sent.

Internal problem with the reader. If the problem persists, contact

Technical Support.

0601 ID BUFFER FULL The tag ID buffer is full. If the problem persists, contact Technical

Support.

0602 REPEATED ID One of the protocols is trying to add an existing tag ID to the

buffer.

Internal problem with the reader. If the problem persists, contact

Technical Support.

0603 NUM IDS TOO LG Internal problem with the reader. If the problem persists, contact

Technical Support.

Table 7 • RFID Error Code Definitions (Continued)

Error

Code RFID Error or

Status Message Description/Action Required

Contents

Main 2008 ZIH Corp. Part Number: 58978L-008 Rev. A Proprietary Statement Product Improvements Liability Disclaimer Limitation of Liability Contents Page Page Page Page Who Should Use This Document How This Document Is Organized Page About This Document Contacts Contacts Document Conventions Bubbledot ICG Page Introduction to RFID RFID Overview RFID Label Selection Considering RFID Transponder (Tag) Types Accounting for Transponder Inlay Placement Selecting and Purchasing RFID Labels Performing Label Placement Tests Storing RFID Labels Radio Frequency Interference ZPL Commands for RFID Applications SGD Commands for RFID Applications Page Set Tag Ty pe Set RF Power Levels Perform RFID Transponder Calibration Download Latest Firmware Page RFID Control Panel Parameters PRINT MODE - RFID + RFID TEST QUICK SLOW RESTORE RUN RFID VALID CTR 956 RESET RFID VOID CTR 23 RESET RFID READ PWR 16 RFID WRITE PWR 16 RFID POWER LOW RFID ANTENNA ANTENNA PORT 1 RFID ERR STATUS RFID TAG TYPE CLASS 1 96-BIT 0x112233445566778899001122 Creating Basic RFID Label Formats Create and Send an RFID Label Format To create an RFID label based on a sample label, complete these steps: COPY FORMAT1.ZPL Sample RFID Label Formats RFID Label Format 1Encode a Gen 2 Tag in Hexadecimal RFID Label Format 2Encode a Gen 2 Tag in ASCII RFID Label Format 3Read Data from Tag and Print Data on Label RFID Label Format 4Encode Tag, Read Tag, and Print Data on Label 0data Page RFID Label Format 5Encode a Class 1 64-bit Tag in Hexadecimal RFID Label Format 6Encode Tag, Read Tag, and Return Results to Host Page RFID Antenna Location Page Page Page Page Basic Transponder Characteristics Electronic Product Code (EPC) EPC Fields EPC Structure in RFID Labels , ~ ! @ # $ % ^ & * | . < > / \ : ; EPC Class 1, Generation 2 (Gen 2) Data Content Data and Tag Security Gen 2 Memory Map Page Page Troubleshooting RFID Problems CALIB Page Page RFID Error Codes and Messages Error and Status Messages Page Page Page Page Page 0003 8405 1237 8010 0404 8012 0044 0400 8002 0407 0603 0043 0102 0055 xxxx F004 0103 Page Page Page 8506 0406 8407 9202 Error Codes Page 0036 0037 0038 0039 003A Page Page 0400 0401 0402 0403 0404 Page Page Page Page Page Page Page ZPL II Commands for RFID Page ZPL Overview Printer and Firmware Compatibility Table 8 shows which RFID ZPL commands you can use with different printers and firmware versions. Table 8 Supported Commands Based on Printer and Firmware 58978L-008 Rev. A RFID Programming Guide 11/14/2008 ^RQ onpage 105 Quick Write EPC Data and Passwords * Table 8 Supported Commands Based on Printer and Firmware (Continued) ^HL or ~HL Return RFID Data Log to Host ^HR Calibrate RFID Transponder Position RUN option in the RFID TAG CALIB control panel parameter performs the same a b RFID TAG CALIB Page ^HV Host Verification ^MM Print Mode Page ^RA Read AFI or DSFID Byte Page ^RB Define EPC Data Structure Page ^RE Enable/Disable E.A.S. Bit N = Y = r ^REy,5 ^RF Read or Write RFID Format Page Page Page ^RI Get RFID Tag ID ^RM Enable RFID Motion e Y = N = ^RN Detect Multiple RFID Tags in Encoding Field MULTIPLE TAGS e Y = N = ~RO Reset Advanced Counters c 1 2 3 4 Page ^RQ Quick Write EPC Data and Passwords A = H = E = c ^FD[EPC],[access],[kill] Page ^RR Specify RFID Retries for a Block ^RS Set Up RFID Parameters t p v n e N = a S = D = c s ^RS ^RS Table 9 Supported Tag Types and Default Values (Continued) ^RS,800,,2,P^FS ^RS,800,500,2,P^FS ^RT Read RFID Tag # b n Page ~RV Report RFID Encoding Results ^RW Set RF Power Levels for Read and Write Page ^RZ Set RFID Tag Password and Lock Tag p Page Page ^WF Encode AFI or DSFID Byte r m w Page ^WT Write (Encode) RFID Tag b r m Page ^WV Verify RFID Encoding Operation e Page SGD Commands for RFID Printer and Firmware Compatibility odometer.rfid.valid_resettable odometer.rfid.void_resettable rfid.error.response rfid.position.program rfid.tag.data rfid.tag.test rfid.tag.type Table 10 SGD RFID Printer and Firmware Compatibility (Continued) odometer.rfid.valid_resettable ! U1 setvar "odometer.rfid.valid_resettable" "reset" odometer.rfid.void_resettable ! U1 setvar "odometer.rfid.void_resettable" "reset" rfid.error.response ! U1 getvar "rfid.error.response" RFID OK NO TAG FOUND rfid.position.program ! U1 setvar "rfid.position.program" "15" rfid.reader_1.antenna_port 1 = 2 = ! U1 setvar "rfid.reader_1.antenna_port" "2" rfid.reader_1.power.read ! U1 setvar "rfid.reader_1.power.read" "high" rfid.reader_1.power.single_power ! U1 setvar "rfid.reader_1.power.single_power" "high" rfid.reader_1.power.write Page rfid.tag.calibrate ! U1 setvar "rfid.tag.calibrate" "restore" ! U1 setvar "rfid.tag.calibrate" "run" rfid.tag.data ! U1 setvar "rfid.tag.data" rfid.tag.test ! U1 setvar "rfid.tag.test" "quick" ! U1 setvar "rfid.tag.test" "slow" rfid.tag.type ! U1 setvar "rfid.tag.type" "gen2" rfid.tag.type rfid.tag.type Table 11 Supported Tag Types and Default Values (Continued) RFID Applicator Signals Timing Diagrams for RFID Single Signal Mode Page Double Signal Mode Applicator Interface Connector Pin Configuration Page Page Jumper Configurations and Pinouts for +5 V I/O Operation Pinouts for +24-28 V I/O Operation Page Index A C D E F G H I J S T V W Z