Husqvarna CZE 4818 manual Control Lever ARM HEX Bolts Neutral Slot

Page 13

ASSEMBLY

Adjustments may be required to get uniform positioning of the control lever. Refer to the "Service and Adjustment" section of this manual.

NOTE: You may now roll or drive the mower off of the skid. Follow the appropriate instruction below to remove the mower from the skid.

CONTROL

LEVER

CONTROL

ARM

HEX

BOLTS

NEUTRAL

SLOT

CZ-2

FIGURE 2

TO ROLL THE MOWER OFF OF THE SKID (See Operation section for location and function of controls

•Move to the rear of the mower, and place the IZT (Integraded Zeroturn Transaxle) bypass linkages into the bypass position to disengage the IZT’s (See “TO TRANS- PORT” in the Operation section of this manual).

•Sitting on the mower, press the deck lift pedal in to the highest cutting position.

•Release park brake lever.

•Roll the mower forward or backward off of the skid.

TO DRIVE THE MOWER OFF OF THE SKID (See Operation section for location and function of controls)

WARNING

Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure the mower is in a well-ventilated area. Be sure the area in front of the mower is clear of other people and objects.

•Be sure all of the above assembly steps have been completed.

•Check engine oil level and fill fuel tank with gasoline.

•Place the IZT(Integraded Zeroturn Transaxle) bypass linkages into the drive position (See “TRANSPORT” in the Operation section of this manual).

•Sit on the seat in the operating posi- tion, set the park brake lever to the on position.

•Rotate the control levers outward into the neutral slot.

•Press forward on the deck lift pedal to raise the deck into the highest cutting position.

•Place the throttle control into the choke position.

•Start the engine. After the engine has started, move the throttle control to the idle position.

•Release the park brake.

•Move the control levers into the operate position.

•Slowly move the control levers for- ward and slowly drive the mower off of the skid.

•Return the control levers back to the neutral position.

•Apply the park brake.

•Turn the ignition key to the “OFF” position.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents CZE Husqvarna. All Rights Reserved Beatrice, NE Contents Symbols and Decals Safety Instructions Safety InstructionsGeneral Use Personal protective equipment Do as follows Driving on SlopesChildren 8011-563 Important Information TransportSpecifications Tools Required for Assembly AssemblyTo Remove the Mower from Crate Before Removing the Mower from the SkidControl Lever ARM HEX Bolts Neutral Slot Check the Tire Pressure ChecklistControls OperationOperation HOW to USE Your MowerDeck Blades EngineTo Adjust the Deck Cutting Height See Fig ERS See Figure To Adjust ANTI-SCALP RollTo Operate on Hills To Transport See Fig To Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips General Recommendations Customer ResponsibilitiesBefore Each USE Operator Presence System Lubrication ChartBlade Care TiresTo Sharpen Blade See Fig BatteryClean AIR INTAKE/COOLING Areas Clean AIR ScreenBelts EngineAIR Filter CleaningEngine OIL Filter Spark PlugsMower Service and AdjustmentTo Level Deck To Replace Deck Belt FRONT-TO-BACK Adjustment See FigIZT Belt Removal To Replace IZT Integraded Zeroturn Transaxle Belt SeeTo Adjust Control Levers See Fig To Adjust the Seat See FigTo Start AN Engine with a Weak Battery To Remove Wheels for RE- PairTo Adjust Park Brake Replacing Battery See FigTracking Adjustment Storage BatteryFuel System Engine OILOther CylindersProblem Cause Correction Troubleshooting PointsTo run when Wiring Schematic ´z+H56¶6M¨ Page 2003W33 114 02
Top Page Image Contents