Husqvarna CZE 4818 manual To Adjust ANTI-SCALP Roll, ERS See Figure, To Operate on Hills

Page 18

OPERATION

 

 

FOOT

 

ANTI-SCALP

 

ROLLER

PEDAL

 

 

 

LIFT

 

 

ARM

 

 

HEIGHT

 

 

PLATE

 

 

CZ-8

FIGURE 6

CZ-9

FIGURE 5

 

TO ADJUST ANTI-SCALP ROLL-

TO OPERATE MOWER

Your mower is equipped with an operator

ERS (See Figure 6)

 

presence system. When the engine is running,

Anti-scalp rollers are properly adjusted when

any attempt by the operator to leave the seat

without first setting the park brake will shut off

they are just slightly off of the ground when the

the engine.

deck is at the desired cutting height in the

• Select desired height of cut.

operating position. Anti-scalp rollers then keep

• Start deck blades by pulling the PTO

the deck in the proper position to help prevent

switch up into the engaged position.

scalping in most terrain conditions.

• To stop the deck blades, press down on

 

NOTE: Adjust Anti-scalp rollers with the mower

the PTO Switch into the disengaged

position.

on a flat level surface.

 

Adjust the deck to the desired cutting height (see “TO ADJUST DECK CUT- TING HEIGHT” in the operation section of this manual).

Using a 3/4" wrench and a 9/16" wrench, remove the nut and shoulder bolt from the anti-scalp roller.

Lower the anti-scalp roller to the ground, and raise it up to the next highest hole.

Replace and tighten the nut and shoulder bolt.

Be sure to adjust all of the anti-scalp rollers to the same position.

Be sure to readjust the anti-scalp rollers if the cutting height is changed.

WARNING

Do not operate the deck without either the entire grass catcher, mulch kit or discharge chute installed.

TO OPERATE ON HILLS

WARNING

Do not drive up or down hills with slopes greater than 10 degrees. And do not drive across any slopes.

IMPORTANT: THE ANTI-SCALP ROLLERS MUST NOT BE USED FOR GAUGE WHEELS OR THE ROLLER AND DECK MAY BE DAMAGED.

18

Image 18
Contents CZE Husqvarna. All Rights Reserved Beatrice, NE Contents Symbols and Decals Safety Instructions Safety InstructionsGeneral Use Personal protective equipment Driving on Slopes Do as followsChildren 8011-563 Transport Important InformationSpecifications To Remove the Mower from Crate AssemblyTools Required for Assembly Before Removing the Mower from the SkidControl Lever ARM HEX Bolts Neutral Slot Checklist Check the Tire PressureOperation ControlsDeck Blades HOW to USE Your MowerOperation EngineTo Adjust the Deck Cutting Height See Fig To Adjust ANTI-SCALP Roll ERS See FigureTo Operate on Hills To Transport See Fig Check Engine OIL Level Before Starting the EngineTo Start Engine See Fig ADD GasolineMowing Tips Customer Responsibilities General RecommendationsBefore Each USE Blade Care Lubrication ChartOperator Presence System TiresBattery To Sharpen Blade See FigBelts Clean AIR ScreenClean AIR INTAKE/COOLING Areas EngineEngine OIL Filter CleaningAIR Filter Spark PlugsService and Adjustment MowerTo Level Deck FRONT-TO-BACK Adjustment See Fig To Replace Deck BeltTo Replace IZT Integraded Zeroturn Transaxle Belt See IZT Belt RemovalTo Start AN Engine with a Weak Battery To Adjust the Seat See FigTo Adjust Control Levers See Fig To Remove Wheels for RE- PairReplacing Battery See Fig To Adjust Park BrakeTracking Adjustment Fuel System BatteryStorage Engine OILCylinders OtherTroubleshooting Points Problem Cause CorrectionTo run when Wiring Schematic ´z+H56¶6M¨ Page 114 02 2003W33