Husqvarna CZE 4818 manual To Replace Deck Belt, FRONT-TO-BACK Adjustment See Fig

Page 28

SERVICE AND ADJUSTMENT

FRONT-TO-BACK ADJUSTMENT (See Fig. 15).

IMPORTANT: DECK MUST BE LEVEL SIDE- TO-SIDE. IF THE FOLLOWING FRONT-TO- BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT OR BOTH REAR LINKAGES EQUALLY SO THE DECK WILL STAY LEVEL.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To obtain the best cutting performance, the deck should be adjusted so the front tip of the blades are approximately 1/8" to 1/4" lower than the rear tip. If the front tip is higher, this will create a poor quality of cut.

FIGURE 15

CZ-19

WARNING

Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.

Check adjustment on the right side of the mower. Position any blade so that the tip is pointing straight forward. Measure distance “B” at the front and rear tip of the blade.

Before making any necessary adjust- ments, check to make sure that the deck is level side-to-side.

With the deck in the highest cutting position, (4 1/2") measure the front tip of the blade to see if the deck is higher or lower than 4 1/2".

To lower the front tip of the blade, using a 9/16" wrench, loosen the hex nuts that are on the front lift linkages (be sure to loosen equal amounts).

When distance “B” is 1/8" to 1/4" lower at the front than rear the adjustment is done.

Reverse above step to raise the deck.

TO REPLACE DECK BELT

DECK BELT REMOVAL (See Fig. 16 and 17)

Park on a level surface. Apply park brake.

Lower the deck into the lowest cutting position

Disengage the tension relief lever from the lock bracket.

WARNING

Lever is spring loaded. Have a tight grip on the lever and release slowly.

Remove screws from both the left and right belt shields, and remove shields.

Remove any dirt or grass that may have accumulated around the cutter housings and entire deck surface.

Carefully roll the belt over the top of the cutter housing pulleys.

Remove the belt from around the electric clutch on the engine shaft.

The belt can now be removed.

28

Image 28
Contents CZE Husqvarna. All Rights Reserved Beatrice, NE Contents Symbols and Decals Safety Instructions Safety InstructionsGeneral Use Personal protective equipment Driving on Slopes Do as followsChildren 8011-563 Transport Important InformationSpecifications Assembly Tools Required for AssemblyTo Remove the Mower from Crate Before Removing the Mower from the SkidControl Lever ARM HEX Bolts Neutral Slot Checklist Check the Tire PressureOperation ControlsHOW to USE Your Mower OperationDeck Blades EngineTo Adjust the Deck Cutting Height See Fig ERS See Figure To Adjust ANTI-SCALP RollTo Operate on Hills To Transport See Fig Before Starting the Engine To Start Engine See FigCheck Engine OIL Level ADD GasolineMowing Tips General Recommendations Customer ResponsibilitiesBefore Each USE Lubrication Chart Operator Presence SystemBlade Care TiresBattery To Sharpen Blade See FigClean AIR Screen Clean AIR INTAKE/COOLING AreasBelts EngineCleaning AIR FilterEngine OIL Filter Spark PlugsMower Service and AdjustmentTo Level Deck FRONT-TO-BACK Adjustment See Fig To Replace Deck BeltTo Replace IZT Integraded Zeroturn Transaxle Belt See IZT Belt RemovalTo Adjust the Seat See Fig To Adjust Control Levers See FigTo Start AN Engine with a Weak Battery To Remove Wheels for RE- PairReplacing Battery See Fig To Adjust Park BrakeTracking Adjustment Battery StorageFuel System Engine OILCylinders OtherTroubleshooting Points Problem Cause CorrectionTo run when Wiring Schematic ´z+H56¶6M¨ Page 114 02 2003W33