Husqvarna CZE 4818 Belts, Engine, Lubrication, Clean AIR Screen, Clean AIR INTAKE/COOLING Areas

Page 25

CUSTOMER RESPONSIBILITIES

NOTE: Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Remove terminal guard.

•Disconnect BLACK battery cable first, then the RED battery cable and remove the battery from the tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until shiny.

•Coat terminals with grease or petroleum jelly

•Reinstall battery (See “REPLACING BATTERY” in the SERVICE AND AD- JUSTMENT section of this manual).

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The Belts are not adjustable. Replace belts if they begin to slip from wear.

ENGINE

LUBRICATION

Refer to you Engine Owners Manual

TO CHANGE ENGINE OIL (See Fig. 10 [Kawasaki]).

•Be sure the mower is on a level surface.

•Oil will drain more freely when warm.

•Place a suitable container under the left rear corner of the rear of the mower.

•Remove oil dipstick. Be careful not to allow dirt to enter the engine when changing oil.

•Using the clear plastic tube included with you mower, place it over the end of the drain valve located on the left side of your engine.

•Place the other end of the tube thru the 2" diameter hole on the left side of the rear deck.

•Be sure container is located under this area of the mower.

•Using a 10 mm wrench, turn the hex head on the oil valve counter clockwise until the oil is draining out of the tube.

After the oil has drained, turn the hex head clockwise until it is tight (do not over tighten).

•Remove the plastic tube from the valve, clean excess oil off of tube and store in a safe place for the next use.

•Refill engine with oil through the oil dipstick tube. Pour slowly. Do not overfill.

•See Engine Owners Manual for type and capacity of the oil.

KAWASAKI ENGINE

OIL DRAIN VALVE

PLASTIC TUBE

FIGURE 10

CZ-13

 

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Refer to your engine manual for the proper cleaning procedure.

CLEAN AIR INTAKE/COOLING AREAS

To insure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents CZE Husqvarna. All Rights Reserved Beatrice, NE Contents Symbols and Decals Safety Instructions Safety InstructionsGeneral Use Personal protective equipment Do as follows Driving on SlopesChildren 8011-563 Important Information TransportSpecifications Tools Required for Assembly AssemblyTo Remove the Mower from Crate Before Removing the Mower from the SkidControl Lever ARM HEX Bolts Neutral Slot Check the Tire Pressure ChecklistControls OperationOperation HOW to USE Your MowerDeck Blades EngineTo Adjust the Deck Cutting Height See Fig ERS See Figure To Adjust ANTI-SCALP RollTo Operate on Hills To Transport See Fig To Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips General Recommendations Customer ResponsibilitiesBefore Each USE Operator Presence System Lubrication ChartBlade Care TiresTo Sharpen Blade See Fig BatteryClean AIR INTAKE/COOLING Areas Clean AIR ScreenBelts EngineAIR Filter CleaningEngine OIL Filter Spark PlugsMower Service and AdjustmentTo Level Deck To Replace Deck Belt FRONT-TO-BACK Adjustment See FigIZT Belt Removal To Replace IZT Integraded Zeroturn Transaxle Belt SeeTo Adjust Control Levers See Fig To Adjust the Seat See FigTo Start AN Engine with a Weak Battery To Remove Wheels for RE- PairTo Adjust Park Brake Replacing Battery See FigTracking Adjustment Storage BatteryFuel System Engine OILOther CylindersProblem Cause Correction Troubleshooting PointsTo run when Wiring Schematic ´z+H56¶6M¨ Page 2003W33 114 02
Top Page Image Contents