Husqvarna CZE 4818 manual Operation, HOW to USE Your Mower, Deck Blades, Engine

Page 16

OPERATION

HOW TO USE YOUR MOWER

TO SET PARKING BRAKE (See Fig. 3)

Your mower is equipped with an operator presence system. When the engine is running, any attempt by the operator to leave the seat without first setting the park brake will shut off the engine.

Pull park brake lever up and to the right to engage the park brake. Make sure the lever is secured to the right.

DECK BLADES

To stop the deck blades, press down on the PTO Switch into the disengaged position.

ENGINE

Move throttle control to slow position.

NOTE: Failure to move the throttle control to slow position and allow engine to idle before stopping may cause engine to “backfire”.

Turn ignition key to “OFF” position and remove key. Always remove key when leaving the mower to prevent unautho- rized use.

Never use choke to stop engine.

IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN “OFF” WILL CAUSE THE BATTERY TO BE DISCHARGED, (DEAD).

TO USE THROTTLE CONTROL (See Fig. 3)

Always operate engine at full throttle. The Throttle control is equipped with a choke detent. Pressing the throttle control all of the way forward will choke the engine. For full throttle, press throttle control forward until you feel resistance.

Operating engine at less than full throttle reduces the battery charging rate

Full throttle offers the best mower perfor- mance.

TO USE CHOKE CONTROL (See Fig. 3)

Use choke control whenever you are starting a cold engine. Do not use to start a warm engine.

To choke, press the throttle control as far forward as it will go.

To take out of choke, pull back on the throttle control until it clicks.

TO MOVE FORWARD AND BACKWARD (See Fig. 4)

IMPORTANT: CONTROL LEVERS RETURN TO NEUTRAL WHEN RELEASED. THIS MAY CAUSE A SUDDEN STOP OF THE MOWER.

The direction and speed of movement is controlled by the control levers on either side of the mower.

The left lever controls the flow of oil in the left IZT (Integraded Zeroturn Transaxle) to the left wheel. The right lever controls the flow of oil in the right IZT to the right wheel.

Motion Control Lever Pattern

(Right Side)

NEUTRAL SLOT

NEUTRAL LOCK

WARNING

Always stop mower completely before

FORWARD

NEUTRAL

FRONT OF MOWER

leaving the operators position; to empty a grass catcher, etc.

REVERSE

FIGURE 4

16

Image 16
Contents CZE Husqvarna. All Rights Reserved Beatrice, NE Contents Symbols and Decals Safety Instructions Safety InstructionsGeneral Use Personal protective equipment Driving on Slopes Do as followsChildren 8011-563 Transport Important InformationSpecifications Assembly Tools Required for AssemblyTo Remove the Mower from Crate Before Removing the Mower from the SkidControl Lever ARM HEX Bolts Neutral Slot Checklist Check the Tire PressureOperation ControlsHOW to USE Your Mower OperationDeck Blades EngineTo Adjust the Deck Cutting Height See Fig ERS See Figure To Adjust ANTI-SCALP RollTo Operate on Hills To Transport See Fig Before Starting the Engine To Start Engine See FigCheck Engine OIL Level ADD GasolineMowing Tips General Recommendations Customer ResponsibilitiesBefore Each USE Lubrication Chart Operator Presence SystemBlade Care TiresBattery To Sharpen Blade See FigClean AIR Screen Clean AIR INTAKE/COOLING AreasBelts EngineCleaning AIR FilterEngine OIL Filter Spark PlugsMower Service and AdjustmentTo Level Deck FRONT-TO-BACK Adjustment See Fig To Replace Deck BeltTo Replace IZT Integraded Zeroturn Transaxle Belt See IZT Belt RemovalTo Adjust the Seat See Fig To Adjust Control Levers See FigTo Start AN Engine with a Weak Battery To Remove Wheels for RE- PairReplacing Battery See Fig To Adjust Park BrakeTracking Adjustment Battery StorageFuel System Engine OILCylinders OtherTroubleshooting Points Problem Cause CorrectionTo run when Wiring Schematic ´z+H56¶6M¨ Page 114 02 2003W33