Husqvarna SMB 70, SMB 70 E EC Declaration of Conformity Only applies to Europe, Noise Levels

Page 37

TECHNICAL DATA

Noise Levels

Equivalent (see note 1) noise intensity at

 

operator’s ear during sawing, meas-

 

ured according to relevant international

 

standards, dB(A)

 

Petrol engine:

97.2

Electric motor:

95.6

Equivalent (see note 1) noise level

 

measured according to relevant inter-

 

national standards, dB(A)

 

Petrol engine:

112.8

Electric motor:

107.4

Vibration Levels

(See note 2)

Vibration level in the handle, during sawing, according to international standards, m/s2

Petrol engine: Electric motor:

2.2

0.7

Note 1: Equivalent noise level is, according to ISO 7182 and ISO 9207, calculated as the time-weighted

energy total for noise levels under various working conditions with the following time distribution: 1/2 idling, 1/2 full load.

Note 2: Equivalent vibration level is, according to ISO 7505, calculated as the time-weighted energy total

for vibration levels under various working conditions with the following time distribution: 1/2 idling, 1/2 full load.

EC Declaration of Conformity (Only applies to Europe)

Directive 98/37/EC, Annex 2 A.

Lennartsfors Verkstads AB, Lennartsfors 1, SE-672 92 ÅRJÄNG, hereby guarantees that the bandsaws Husqvarna SMB 70 and SMB 70 E, with serial numbers 02 100001 – 02 5200100, meet the standards prescribed in the COUNCIL’S DIRECTIVES:

-of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.

-of May 3, 1989 ”relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements.

-of February 19, 1973 ”concerning electrical equipment”, 73/23/EEC

For information regarding noise emissions, see the Technical Data chapter.

The following harmonised standards have been applied: EN292-1, EN 1807:1999, 60204:1

Registered body: 0404, SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has carried out EU type approval in accordance with article 8, section 2c. The EU type approval certificate is numbered 404/02/854.

The supplied bandsaw conforms with the example that underwent EU type approval.

Årjäng February 14, 2002

Lennartsfors Verkstads AB

Örjan Gustafsson, Product Manager

English 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents SMB SMB 70 E Table of Contents Introduction IntroductionSymbols KEY to SymbolsSafety Regulations Safety RegulationsPersonal Protective Equipment Fuel Safety One-man Sawmill Safety EquipmentSafety During Use PersonnelOne-man Sawmill Petrol Engine DescriptionTools and operator’s manual One-man Sawmill Electric Motor Description Carriage FIG Height Setting FIGFrame and FIG Handlebars FIG Cleaning Tank FIGBand Wheels FIG Bandsaw and Band Guide FIGRails Height Adjustment BLog Bolsters a Folding Stops CRail Stop Adjustable Support FeetRail Guard Safety Devices Installation InstallationInstallation Site UnpackingSaw Carriage Setting up the Saw CarriageAssembling the Saw Carriage Saw Carriage Adjustment Band Cleaning Tank FIG Propulsion Wire adjustmentPetrol Engine Electric MotorBandsaw Blade Scale FIG Fuel Fuel HandlingPetrol FuellingStarting a Cold Petrol Engine Starting and StoppingStopping a Petrol Engine Starting a Warm Petrol EngineStarting the Electric Motor Starting the Electric SawmillStopping the Electric Motor Securing the Log USESawing Calculating the YieldStarting the Petrol Engine Edging Dismantling MaintenanceMaintenance Maintenance Drive Belt FIG Band Wheel AdjustmentChecking the Braking Function Saw Unit’s Height AdjustmentDaily Maintenance MaintenancePetrol Engine Technical DataNoise Levels EC Declaration of Conformity Only applies to Europe38 ´z+H66¶6R¨ English ´z+H66¶6R¨
Top Page Image Contents