Ryobi RY10518, RY10520 manuel dutilisation Cleaning the AIR Filter, See Figures 61

Page 33

MAINTENANCE

Use the following instructions to tighten the mount- ing screw of the nose guard. These are specially hardened screws. If you cannot install the screw tightly, replace both the screw and the SAFE-T-TIP®before further operation.

NOTE:  Do not replace the screw with an ordinary screw. Use only identical replacement parts from the manufacturer when replacing parts.

In addition to preventing chain contact with solid objects at the nose of the bar, the SAFE-T-TIP®also helps keep the chain away from abrasive surfaces, such as the ground. Keep it on the right hand side of the bar where it will be between the chain and the ground during flush with ground cutting.

The mounting screw requires a 5/16 in. wrench (or adjustable wrench) to achieve the recommended torque of 35 to 45 in.lb. A torque within this range can be achieved by using the following method.

nTighten the screw with wrench until snug.

nFrom the snug position, tighten the screw an additional 3/4 of a turn using a wrench.

CLEANING THE AIR FILTER

See Figures 61 - 64.

nFor access to the air filter and carburetor area, loosen the three screws holding the cylinder cover.

nActivate chain brake.

nLift the front of the cylinder cover past chain brake lever.

nLift the back of the cylinder cover past handle.

nBefore removing the air filter from the carbure- tor, blow or brush as much loose dirt and saw- dust from around the carburetor and chamber as possible.

NOTE: Make sure to pull the choke rod out to keep the carburetor from being contaminated.

nRemove the screw securing the air filter.

nPosition a flat screwdriver between the tabs and twist to release from the air filter base.

nLift the air filter off the air filter base.

Choose one of the following cleaning options:

nTo lightly clean, tap the filter against a smooth, flat surface to dislodge most saw dust and dirt particles.

 

CYLINDER

SCREW

COVER

 

SCREWS

Fig. 61

AIR FILTER

AIR FILTER

RETAINING

SCREW

Fig. 62

FAN

HOUSING

BAFFLE

PRE-FILTER

 

STARTER ASSEMBLY

Fig. 63

 

nAfter every 5 hours of operation, clean in warm soapy water, rinse, and let dry completely. Replace with a new filter after every 25 hours of use.

NOTE: An alternate method is to clean the filter with compressed air. Always wear eye protec- tion to avoid eye injury.

nReinstall air filter, making sure that tabs on air filter are located in channels on air filter bottom before tightening filter retaining screws.

Page 33 — English

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Toutes LES Versions Todas LAS Versiones Save this Manual for Future ReferenceTable of Contents General Safety Rules  Use safety footwear. Wear snug-fittingRead ALL Instructions  Do not adapt the powerhead to a bow guide Specific Safety RulesRefueling do not Smoke Kickback Tighten the fuel cap securely after refueling Symbols Service Symbol Signal MeaningGlossary of Terms Product Specifications FeaturesChoke Lever Know Your Chain SAWFront Hand GUARD / CHAIN Brake LOW Kickback SAW ChainOperation AssemblyUnpacking Packing ListMixing the Fuel Do not USE E85 FUEL. IT will Void Your WarrantyOxygenated Fuels Premium Exact MIX GasolineFilling the Fuel Tank Adding BAR and Chain LubricantSee Figure Starting the Engine Operating the Chain BrakeSee Figures 4 See Figures 6To Start a Warm Engine Adjusting Idle Speed Stopping the EngineSee Figures 12 Pull and Push Kickback Precautions Preparing for Cutting Proper Grip on HandlesSee Figures 16 Proper Cutting Stance Work Area PrecautionsProper Procedure for Tree Felling Felling Trees Hazardous ConditionsSee Figures 21 Removing Buttress Roots Bucking with a Wedge BuckingBucking Logs Under Stress OverbuckingUnderbucking Limbing and Pruning Cutting SpringpolesSee Figures 31 General Maintenance MaintenanceLubrication Replacing the Guide BAR and ChainCutters Chain Rotation Chain Drive Links BAR Groove BAR Studs Adjusting PIN See Figures 44 Adjusting the Chain TensionSee Figures 47 Chain MaintenanceSee Figures 49 Sharpening the CuttersSide Plate Angle TOP Plate Filing AngleMaintaining Depth Gauge Clearance SeeMounting the SAFE-T-TIPNOSE Guard Maintaining the Guide BARMaintaining the SAFE-T-TIPNOSE Guard See Figures 59Cleaning the AIR Filter Choose one of the following cleaning optionsSee Figures 61 Adjusting the Carburetor Cleaning the Starter UnitChecking the Fuel Filter Cleaning the EngineReplacing the Spark Plug See Figures 67When storing 1 month or longer Inspecting and Cleaning Chain BrakeSpark Arrestor Storing the ProductEmissions Maintenance Schedule Emissions Parts Inspect Clean ReplaceOr Yearly Troubleshooting BAR and Chain CombinationsRUN l posi Refer to Replacing the Guide Bar and Chain Speed. Refer to Adjusting the CarburetorLimited Warranty Statement Warranty41 English Règles DE Sécurité Générales AVERTISSEMENT Lire Toutes LES Instructions  Ne pas adapter le bloc-moteur à un guide Règles DE Sécurité ParticulièresRebond Approvisionnement EN Carburant NE PAS FUMER TIP SymbolesDépannage Symbole Signal SignificationGlossaire Spécifications CaractéristiquesLevier DE Volet DE Départ Pour SE Familiariser Avec LA Scie À ChaîneProtection DE Poignée Avant / Frein DE Chaîne GuideUtilisation AssemblageDéballage Liste DE Contrôle D’EXPÉDITIONMélange DU Carburant Carburants OxygénésMélange Premium Exact Remplissage DU Réservoir DE Carburant Appoint DE Lubrifiant Pour Guide ET ChaîneVoir la figure Démarrage DU Moteur Utilisation DU Frein DE ChaîneVoir les figures 4 et Voir les figures 6 àDémarrage du moteur chaud  MarcheArrêt DU Moteur Réglage DuralentiVoir les figures 12 et Poussée ET Traction Voir les figures 16 et Précautions À Prendre Pour Éviter LE RebondPosition DE Coupe Correcte Précautions À Prendre SUR LE Lieu DE TravailMéthodes D’UTILISATION / Coupe Élémentaires Abattage D’ARBRES Situations Dangereuses AVERTISSEMENT  Méthode Correcte D’ABATTAGEVoir les figures 21 à Élimination DES Racines Échasses AVERTISSEMENT REBONDDébitage Débitage DE Billes Sous ContrainteÉbranchage ET Émondage Coupe DE FouetsVoir les figures 31 et Entretien Remplacement DU Guide ET DE LA ChaîneEntretien Général Lubrification26 Français 27 Français Voir les figures 44 à Réglage DE LA Tension DE ChaîneVoir les figures 47 et Entretien DE LA ChaîneAffûtage DES Dents Voir les figures 49 àVoir Réglage de la tension de chaîne Angle DE Plaque Latérale Angle D’AFFÛTAGE DE LA Plaque SupérieureMaintien DU JEU DU Limiteur DE Profondeur Voir les figures 55 àEntretien DU Guide Installation DE LA Garde SAFE-T-TIPT R E T I E N D E L a G a R D E SAFE-T-TIP Voir les figures 59 etVoir les figures 61 à Nettoyage DU Filtre À AIRRéglage DU Carburateur Nettoyage DU LanceurAvertissement Voir le etNettoyage DU Moteur Remplacement DE LA BougieVérification DU Filtre À Carburant Voir les figures 67 àInspection ET Nettoyage DU Frein DE Chaîne PARE-ÉTINCELLESRemisage LE Produit Voir les figures 71 etNous Appeler D’ABORD Combinaisons DE Guide ET Chaîne Dépannage45 cm 18 pulg 310628001 Réglage de la tension de chaîne de la section Entretien de Énoncé DE LA Garantie Limitée Garantie41 Français Advertencia Reglas DE Seguridad GeneralesReglas DE Seguridad Específicas Contragolpe Reabastecimiento DE Combustible ¡NO FumeSímbolo Nombre Denominación / Explicación SímbolosSímbolo Señal Significado Peligro ServicioCausará la muerte o lesiones serias Corte trasero de tala Glosario DE TérminosEspecificaciones DEL Producto CaracterísticasPalanca DEL Anegador Familiarícese CON LA MotosierraProtección Delantera DE LA Mano / Freno DE LA Cadena Barra GuíaDesempaquetado ArmadoLista DE Empaquetado AplicacionesCombustibles Oxigenados Mezclado DEL CombustiblePremium Exact MIX Gasolina No USE Combustible E85. Anulará SU GarantíaLlenado DEL Tanque Abastecimiento DE Lubricante Para LA Barra Y LA CadenaVea la figura Arranque DEL Motor Funcionamiento DEL Freno DE LA CadenaVea las figuras 4 y Vea las figuras 6 aPrecaución Anegación MáximaPara arrancar con el motor caliente Apagado DEL Motor Ajuste DE LA Marcha LentaVea las figuras 12 y Empujón Y Tirón Vea las figuras 16 y Precauciones Relacionadas CON EL ContragolpePostura Correcta Para EL Corte Precauciones Relacionadas CON EL Área DE TrabajoProcedimientos Básicos DE Funcionamiento Y Corte Tala DE Árboles Condiciones Peligrosas Advertencia Procedimiento Correcto Para Talar ÁrbolesVea las figuras 21 a Eliminación DE Raíces Zancas Tronzado CON Cuña TronzadoTronzado DE Troncos Bajo Tensión Tronzado POR ArribaTronzado POR Abajo Desramado Y Poda Corte DE PértigasVea las figuras 31 y Mantenimiento General MantenimientoLubricación Cómo Reemplazar LA Barra Guía Y LA CadenaEslabones DE Impulsión DE LA Cadena Pernos DE Montaje DE LA Barra Pasador DE Ajuste Vea las figuras 44 a Ajuste DE LA Tensión DE LA CadenaVea las figuras 47 y Mantenimiento DE LA CadenaVea las figuras 49 a Afilado DE LOS Dientes DE CorteÁngulo DE Limadura DE LA Placa Superior Ángulo DE LA Placa LateralVea las figuras 55 a Mantenimiento DE LA Barra Guía Montaje DE LA Protección SAFE- T-TIPDE LA PuntaVea las figuras 59 y Limpieza DEL Filtro DE Aire Vea las figuras 61 aEscoja una de los siguientes métodos optativos de limpieza Ajuste DEL Carburador Limpieza DE LA Unidad DEL ArrancadorVea la figura 65 y Antes de ajustar el carburadorRevisióndelfiltrodecombustible Limpieza DEL MotorCambio DE LA Bujía Vea las figuras 67 aInspección Y Limpieza DEL Freno DE LA Cadena ParachispasAlmacenamiento DE LA Producto Vea las figuras 71 yLlámenos Primero Combinaciones DE Barra Y Cadena Solución DE ProblemasNúm. pieza Barra Barra guía CadenaFuncionamiento del freno de la cadena en la sección Declaración DE LA Garantía Limitada GarantíaPágina 41 Español Manual DEL Operador Manuel D’UTILISATIONAVERTISSEMENT  Advertencia

RY10518, RY10520 specifications

The Ryobi RY10518 and RY10520 are two popular models in the Ryobi lineup of outdoor power equipment, specifically designed for homeowners and DIY enthusiasts seeking efficient and reliable string trimmers. Both models showcase innovative features, advanced technologies, and practical characteristics that make yard maintenance tasks more manageable and enjoyable.

The Ryobi RY10518 is powered by a robust 18-volt lithium-ion battery that delivers efficient performance. Its lightweight design makes it easy to maneuver, reducing user fatigue, especially during extended use. The RY10518 features an automatic feed spool, which allows for continuous line advancement without bumping the trimmer against the ground, simplifying the trimming process. The adjustable telescoping shaft enables users to customize the length of the trimmer to suit their height and comfort level.

On the other hand, the Ryobi RY10520 offers more power with its 40-volt lithium-ion battery. This model is designed for those who require a little extra power for tougher vegetation and larger yards. The RY10520 also features an automatic feed spool for hassle-free operation. Its dual-line system provides a wider cutting swath, making it efficient for trimming larger areas quickly. Additionally, the RY10520 is equipped with a brushless motor, which enhances the tool's runtime and overall efficiency, allowing for longer work sessions without the need for frequent recharges.

Both models incorporate Ryobi's signature One+ battery technology, which means that the batteries are interchangeable with other Ryobi tools in the One+ lineup. This feature makes it convenient for users who already own Ryobi products, as they can use the same batteries across multiple tools.

Another defining characteristic of the RY10518 and RY10520 is their user-friendly design. The ergonomic handles provide a comfortable grip, and the safety features ensure peace of mind during operation. Additionally, both models are designed for easy storage, with a compact design that allows them to fit conveniently in garages or tool sheds.

In conclusion, the Ryobi RY10518 and RY10520 are versatile, efficient, and user-friendly string trimmers that cater to a variety of landscaping needs. Whether you opt for the lighter RY10518 perfect for small gardens or the powerful RY10520 ideal for larger areas, both models exemplify Ryobi’s commitment to providing high-quality outdoor power equipment. With their innovative features and technologies, they offer an excellent choice for anyone looking to maintain their yard with ease.
Top Page Image Contents