Ryobi RY26500, RY26901, CS26 Attaching the Storage Hanger, Attaching the J Handle BC26

Page 14

ASSEMBLY

ATTACHING THE STORAGE HANGER

See Figure 3.

There are two ways to hang your attachment for storage.

To use the hanger cap, push in the button and place the hanger cap over end of the lower end attachment shaft. Slightly rotate the cap from side to side until the button locks into place.

The secondary hole in the attachment shaft can be used for hanging purposes as well.

ATTACHING THE FRONT handle - CS26 and SS26

See Figure 4.

Remove wing nut, washer, and bolt from the front handle.

Install the front handle onto the top side of the drive shaft housing in the area indicated by the label.

NOTE: The open side of the handle should face the operator. 

Place the bolt through the front handle.

NOTE: The hex bolt head fits inside the hex recess molded into one side of the handle.

Reinstall the washer and wing nut.

Tighten wing nut securely.

ATTACHING THE “J” HANDLE - BC26

See Figure 5.

A “J” handle must be used for ensuring the best control and maximizing operator safety when using a brushcutter.

Place the bottom J-handle clamp on the drive shaft as shown. Insert the tab on the top J-handle clamp into the slot on the bottom J-handle clamp.

Insert the end of the J-handle between the clamps so that holes align and handle will be located to the operator’s left.

Push the bolt through the clamp and handle.

Install flat washer, lock washer, and wing nut to hold the assembly in place.

Adjust the position of the handle to the area indicated by the label on the drive shaft housing.

Tighten the wing nut securely.

Attaching the GRASS DEFLECTOR

WARNING:

The line cutting blade on the grass deflector is sharp. Avoid contact with the blade. Failure to avoid contact can result in serious personal injury.

To attach the curved shaft grass deflector - CS26

See Figure 6.

Remove hex screw, flat washer, and wing nut from grass deflector.

Press the grass deflector onto the bottom of the curved shaft as shown.

Insert the hex screw through the grass deflector and the bracket on the curved shaft.

Place the flat washer on the hex screw.

Place the wing nut on the hex screw and tighten securely.

To attach the straight shaft grass deflector - SS26

See Figure 7.

Remove the wing screw from the grass deflector.

Insert the tab on the mounting bracket in the slot on the grass deflector.

Align the screw hole in the mounting bracket with the screw hole in the grass deflector.

Insert the wing screw through the mounting bracket and into the grass deflector.

Tighten the screw securely.

ATTACHING THE brushcutter Guard - BC26

See Figure 8.

The guard is shipped installed on these brushcutter models. Instructions have been included for reference when changing from string trimmer operation back to brushcutter operation.

With the string head removed, place the brushcutter guard on the gear head as shown.

Install the three hex head screws from bottom through the guard and into the gear head.

Tighten the screws securely and torque to 40-50 in.lb. minimum.

ATTACHING THE Shoulder harness - BC26

See Figure 9.

Connect the latch on the shoulder harness to the strap hanger.

Adjust the strap to a comfortable position.

CONVERTING FROM BRUSHCUTTER to string trimmer - BC26

To convert from the brushcutter to the string trimmer, remove the blade and brushcutter guard, attach the straight shaft grass deflector and install the string head.

8 — English

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Toutes LES Versions Save this Manual for Future ReferenceCS26 RY26500 RY26901 Todas LAS VersionesPage BC26 CS26SS26 Bobine À FIL Fixe Dual SpooltmBolt boulon, perno DE LA Herramienta Proper Operating PositionBonne Position DE Travail Carrete Insert Line through slots until approx Vii Table of Contents General Safety Rules Read all instructionsSpecific safety rules for ­ brushcutter and blade use Specific Safety RulesSpecific safety rules for trimmer use Symbol Signal Meaning SymbolsSymbol Name ExplanationGrass Deflector FeaturesService TOP-MOUNTED MotorRemoving the attachment from the power head AssemblyInstallING the Power Head to the Attachment UnpackingAttaching the Storage Hanger Attaching the J Handle BC26Converting from String Trimmer to Brushcutter BC26 Installing the Tri-ArcBlade and brushcutter guardRemoving the Tri-Arcblade and brushcutter guard Removing the straight shaft grass deflector and String headOxygenated Fuels OperationFueling and Refueling the trimmer Operating the TrimmerGrass Deflector line Trimming CUT-OFF Blade To Advance the Cutting line bump feed string headCutting Tips Operating the BrushcutterStarting and Stopping Tri-ArcBLADECutting Technique Blade See Figures 21Maintenance General MaintenanceStoring the Product Cleaning the Exhaust Port and Muffler Spark ArrestorFuel CAP Speed. See Figure TroubleshootingGap. Refer to Spark Plug Replacement earlier Warranty This product was manufactured with a catalyst mufflerLimited Warranty Statement MANUFACTURER’S Warranty Coverage Règles DE Sécurité Générales Lire Toutes LES InstructionsRègles DE Sécurité Particulières Explication SymbolesSymbole Nom Caractéristiques Liste des pièces Installation DU BLOC-MOTEUR SUR L’ACCESSOIREDéballage AvertissementAssemblage Conversion DE Débroussailleuse EN TAILLE-BORDURES BC26 Installation DE LA Bandoulière BC26Installation DE LA Lame TRI-ARCET DU PARE-DÉBRIS Retrait DE LA Lame TRI-ARCET DU PARE- DébrisCarburants Oxygénés UtilisationApprovisionnement EN Carburant Lame DE Sectionnement DE Ligne DE Utilisation DU TAILLE-BORDURESConseils DE Coupe Avertissement Coups DU Déflecteur D’HERBETechniques DE Coupe Lame Avertissement Ricochet DE LameLame TRI-ARC Démarrage ET ArrêtEntretien Remplacement DE LA BobineInstallation de la bobine à fil fixe Dual Spool Entretien GénéralRéglage du ralenti REMPLACement de la BougieNettoyage DU Filtre À AIR Écran Remisage le produitDépannage Garantie ’AIDEÉnoncé DE LA Garantie Limitée Responsabilités DU Propriétaire Dans LE Cadre DE LA Garantie Lea todas las instrucciones Reglas DE Seguridad GeneralesAdvertencia Reglas DE Seguridad Específicas Precaución SímbolosPeligro ExplicatiónCaracterísticas Lista de empaquetado ArmadoDesempaquetado Instalación DEL Cabezal Motor EN EL AditamentoMontaje DE LA ASA DE ALMACENAMIENTO Montaje DEL Deflector DE Pasto AdvertenciaConversión de recortadora de hilo a desbrozadora BC26 Montaje de la correa para el hombro BC26Conversión de desbrozadora a recortadora de hilo BC26 Vea las figuras 10 yCombustibles Oxigenados FuncionamientoLlenado DEL Tanque Cuchilla DE Corte DEL Hilo EN EL Deflector DE Hierba Manejo DE LA RecortadoraSugerencias Para Cortar Utilización DE LA DesbrozadoraTécnica DE Corte CON Cuchilla Advertencia Contragolpe DE LA CuchillaCuchilla Tri-Arc Arranque Y ApagadoReemplazo DEL Carrete MantenimientoMantenimiento General Vea las figuras 24Tapa DEL Tanque DE Combustible Advertencia Limpieza DEL Orificio DE Escape Y DEL SilenciadorParachispas Solución DE Problemas El motor no arranca No hay chispaGarantía 4050Declaración DE LA Garantía Limitada Cobertura DE LA Garantía DEL Fabricante Page Proposition 65 DE L’ÉTAT DE Californie Manuel D’UTILISATION / Manual DEL OperadorCalifornia Proposition California Propuesta DE LEY NÚM
Related manuals
Manual 48 pages 50.23 Kb

RY26500, CS26, RY26901 specifications

The Ryobi CS26 is a versatile and powerful gas string trimmer designed for homeowners and landscape professionals alike. Featuring a 26cc, 2-cycle engine, the CS26 provides ample power to tackle tough grass and brush, ensuring that your yard work is completed with ease and efficiency. One of its standout features is the Easy Start technology, which significantly reduces the effort required to start the engine. This user-friendly feature allows both seasoned landscapers and newcomers to get the job done without the frustrating pull-start experience.

The CS26 incorporates a lightweight design, weighing in at just around 10 pounds, which enhances maneuverability and reduces operator fatigue during extended use. Its straight shaft design also provides better reach and the ability to navigate around hard-to-reach areas, such as under low-hanging branches or fences.

In terms of cutting capabilities, the Ryobi CS26 is equipped with a durable .095-inch diameter line. This heavy-duty line provides exceptional cutting performance and is designed to withstand the rigors of tough landscaping tasks. The trimmer also features an Easy Reload head, allowing users to quickly and efficiently replace the cutting line without the need for disassembly.

Additionally, the CS26 boasts an adjustable handle that provides comfort and better control while trimming. Users can customize the handle position to fit their preferred working stance, further enhancing the overall user experience. The anti-vibration technology integrated into the design helps to minimize hand fatigue, allowing for longer operation periods without discomfort.

The Ryobi CS26 is not only powerful but also eco-conscious. Its engine design offers lower emissions compared to older models, making it a suitable choice for users who are environmentally aware. The trimmer's capabilities make it ideal for various landscaping tasks, including edging, trimming, and clearing dense brush.

In summary, the Ryobi CS26 gas string trimmer combines power, ease of use, and comfort to create an efficient landscaping tool. With features such as Easy Start technology, a lightweight design, durable cutting line, and adjustable handles, it meets the demands of both homeowners seeking to maintain their lawns and professionals looking for reliable equipment to add to their toolkit. For anyone in search of a dependable string trimmer, the Ryobi CS26 represents an excellent choice that will deliver impressive results.
Top Page Image Contents