Roberts Gorden BH-60, BH-40, BH-150, BH-175, BH-115 Grille End Cap Installation, Grille Installation

Page 40

BH-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL

7.6Protective Grille Installation Step 7.6.1 Silicone Cap Installation

	Silicone Cap
Grille	Description	Part Number
Finger	Grille Section	08050001
	Grille End Cap	08050002
	Silicone Cap	91915951-6P

Step 7.6.2 Grille End Cap Installation
A	B
Grille	Grille End Cap
C	D
	Bend up 90°.
	Pull outward.

Step 7.6.3 Grille Installation

Reflector

40"

(101 cm)

Final Grille

Section

Grille

Grille

End Cap

34 of 59

Image 40

Contents Economical Unitary Page Roberts-Gordon LLC Page Table of Figures Page Heater Safety Manpower RequirementsSafety Labels and Their Placement California PropositionTop and Bottom Panel Label Placement DescriptionSide and Back Panel Label Placement Description Part NumberWall Tag Installer ResponsibilityNational Standards and Applicable Codes Maintain clearances to combustibles at all times for safety Clearances are the required distances thatC D InchesCentimeters 45 Tilt Reflector Model Tube, Standard Reflector ModelTube, Opposite 45 Reflector Model Inches CentimetersUnvented VentedNational Standards and Applicable Codes Major Components Stainless SteelBurner Tube Reflector End CapStandard Parts List Contents of BH-Series Burner CartonCore Packages Minimum Standard Aluminized Heater Installation Critical Hanger Placement Run Length Typical ExpansionLinear Heater Assembly Overview Linear Heater Layout Overview Burner Tube Installation Linear Heater Layout OverviewCoupling and Tube Assembly Tube Clamp Package InstallationTube Clamp Package 1 Coupling and Tube Assembly 2 Coupling and Tube AssemblyTube Length ModelTurbulator Installation Turbulator InstallationHanger Burner Tube Reflector 1 Reflector, U-Clip and Reflector Support Installation Description Part Number Reflector Support PackageBurner Installation Optional Heater Accessories Tube Heater Assembly Overview Tube Heater Layout Overview Elbow Package Configuration .2.1 Elbow Installation Between Burner and ElbowElbow Package Clip Package2 Elbow Installation 5 Reflector Joint Detail Reflector Joint DetailReflector Side Extension 1 Bracket Installation 2 Side Reflector InstallationDescription Part Number Lower Clearance Shield Package Distance a Extension 2 Frame Shield InstallationDescription Part Number Reflector Side Extension 01370412 2 Grille End Cap Installation 3 Grille InstallationUnited States Requirements VentingCanadian Requirements Unvented Operation Horizontal VentingVertical Venting Unvented Operation Tube TerminationVertical Ventilation 4 10 cm Pipe Common Side Wall VentingCommon Vertical Venting Outside Combustion Air Supply Vertical Outside Air Supply for Single Heater InstallationDescription Part Number Vent Cap 4 10 cm 90502300 Vertical Outside Air Supply for Double Heater Installation Description Part Number Vent Cap 6 15 cm 90502302GAS Piping When attaching gas hose Correct PositionsHold gas nipple securely with pipe wrench Failure to follow these instructions can resultWiring Line Voltage Thermostat WiringLow Voltage Thermostat Wiring Front ViewInternal Wiring Ladder Diagram Electrical Connection to the Burner Operation and Maintenance Pre-Season Maintenance and Annual InspectionSequence of Operation To Shut Off HeaterVicinity of the Heater Vehicles and OtherObjects ReflectorSafety Labels Blower Scroll, WheelMotor Burner Cup and Orifice ElectrodeTroubleshooting Troubleshooting Flow Chart YESPage Manifold Gas Pressure Setting Replacement Parts Replacement Parts Description Part Number General Specifications DimensionsGAS Pressure AT Manifold Pipe ConnectionPage Warranty is Void if ROBERTS-GORDON LLC will PAY forROBERTS-GORDON LLC will not PAY for Limitations on Authority RepresentativesPage Page Page

Related manuals

Manual 70 pages 23.9 Kb

Manual 20 pages 37.5 Kb