Craftsman 358.79101 instruction manual Unit / Maintenance Safety, Fuel Safety, Cutting Safety

Page 3

Ifsituationsoccurwhicharenotcov- eredinthismanual,usecareand goodjudgmentIfyouneedassis.- tance,contactyourSearsService Centerorcall1-800-235-5878.

OPERATORSAFETY

Dress properly. Always wear safety glasses or similar eye protection when operating, or performing maintenance, on your unit (safety glasses are avail-

able). Eye protection should be marked Z87.

Always wear face or dust mask if op- eration is dusty.

Always wear hea W, long pants, long sleeves, boots, and gloves. Wearing safety leg guards is recommended.

Always wear foot protection. Do not go barefoot or wear sandals. Stay clear of spinning line.

Secure hair above shoulder length. Secure or remove loose clothing or clothing with loosely hanging ties, straps, tassels, etc. They can be caught in moving parts.

Being fully covered also helps protect you from debris and pieces of toxic plants thrown by spinning line.

Stay Alert. Do not operate this unit when you are tired, ill, upset or under the influence of alcohol, drugs, or medication. Watch what you are do- ing; use common sense.

Wear hearing protection.

Never start or run inside a closed

room or building. Breathing exhaust fumes can kill.

Keep handles free of oil and fuel.

UNIT / MAINTENANCE SAFETY

Disconnect tile spark plug before per- forming maintenance except carbure- tor adjustments.

Look for and replace damaged or loose parts before each use. Look for and repair fuel leaks before use. Keep in good working condition.

Replace trimmer head parts that are chipped, cracked, broken, or dam-

aged in any other way before using the unit.

Maintain unit according to recom- mended procedures. Keep cutting line at proper length.

Use only 0.080 inch (2 mm) diameter Craftsman(R_ brand line. Never use

wire, rope, string, etc.

Install required shield properly before using the unit. Use only specified trim- mer head; make sure it is properly installed and securely fastened.

Make sure unit is assembled correctly as shown in this manual.

Make carburetor adjustments with lower end supported to prevent line from contacting any object.

Keep others away when making car- buretor adjustments.

Use only recommended Craftsman® accessories and replacement parts.

Have all maintenance and service not

explained in this manual performed by a Sears Service Center.

FUEL SAFETY

Mix and pour fuel outdoors.

Keep away from sparks or flames.

Do not smoke or allow smoking near fuel or the unit.

Avoid spilling fuel or oil. Wipe up all fuel spills.

Move at least 10 feet (3 meters) away from fueling site before starting en- gine.

Stop engine and allow to cool before removing fuel cap.

Always store gasoline in a container approved for flammable liquids.

CUTTING SAFETY

_'WARNING:

Inspect the area be-

fore each use. Remove objects (rocks, broken glass, nails, wire, etc.) which can be thrown by or become entangled in line. Hard objects can damage the trimmer head and be thrown causing serious injury.

Use only for trimming, scalping, mow- ing and sweeping. Do not use for edg- ing, pruning or hedge trimming.

Keep firm footing and balance. Do not overreach.

Keep all parts of your body away from

muffler and spinning line. Keep engine below waist level. A hot muffler can

cause serious burns.

Cut from your left to your right. Cutting on right side of the shield will throw debris away from the operator.

Use only in daylight or good artificial light.

Use only for jobs explained in this manual.

TRANSPORTING AND STORAGE

Allow engine to cool; secure unit be- fore storing or transporting in vehicle.

Empty the fuel tank before storing or transporting the unit. Use up fuel left in the carburetor by starting the en- gine and letting it run until it stops.

Store unit and fuel in area where fuel vapors cannot reach sparks or open

Image 3
Contents Gasoline Weedwaoker Sears, Roebuck and Co., D/817 WA, Hoffman Estates, IL This power unit can be dangerous! OpTransporting and Storage Unit / Maintenance SafetyFuel Safety Cutting SafetyMotorsswitches,furnaces,etc Fueling Engine Stop SwitchPrimer Bulb Before Starting EngineStarting a Warm Engine HOW to Stop Your UnitHOW to Start Your Unit Starting a Cold EngineCutting Methods Operating InstructionsOperating Position Trimmer Line AdvanceTrimming SweepingLabels Maintenance Schedule Care & Maintenance TaskClean AIR Filter General Recommen DationsReplacing the Cutting Head Line ReplacementCarburetor Adjustment Replace Spark PlugInternal Engine Idle Speed AdjustmentSeasonal Storage Fuel SystemTroubleshooting Table CauseRemedy Your Warranty Rights and OB Warranty CommencementOr Replacement of PARTS. Re NANCE, Replacement and RE- Pair of Emission Related DEL Aparato Sears, Roebuck and Co., D/817 WA Hoffman Estates, ILAdvertencia Manual DE Informacion InstruccionesSeguridad DEL Usuario Seguridad DEL Aparato Y EN EL MantenimientoSeguridad CON EL Combustible Seguridad AL Cortar Transporte Y AlmacenamientoAviso DE Seguridad El estar ex Contenico DE LA Caja MontajeAjuste DEL Mango Antes DE Poner EN Marcha EL Motor Abastecimiento DEL MotorPalanca DEL Arrancador Para Arrancar CON EL Motor Caliente Para Detener EL MotorPara Poner EN Marcha EL Motor Para Arrancar CON Motor FrioMetodos DE Corte Instruccionesde USOPara Escalpar i J Cronograma DE Mantenimiento Verifique QUE no Haya FIJA- Dores NI Piezas SueltasInspeccione LA Rejilla Anti Chispa Y EL Silenciador Cambie LA Bujia Reemplazo DE LA LineaReemplazo DE LA Cabezal DE Corte Marcha Lenta Ajuste AL CarburadorOtros Interior DEL MotorCausa Tabla DiagnosticaFecha DEL Comienza DE LA GA SUS Derechos Y ObligacionesBierta DE Garantia DEL Fabri Rantia DE Responsabilidad DE DEL Dueiio Como dueiho de una41 1 61 1 81 RECLAMACIONSicuentaustedcon manual de instrucciones